manualshive.com logo in svg

Bay Networks Remote Annex 2000, Hardware Installation Manual, Page: 11 / 136

Share
Download
Bay Networks Remote Annex 2000 Hardware Installation Manual Download Page 11

xiii

Remote Annex 2000 Hardware Installation Guide

Preface

T

his guide describes how to install a Remote Annex 2000 on a local

area network (LAN).

See the Annex Quick Start or the Remote Annex Software Installation
Notes that come with your Remote Annex 2000 for a description of
the software installation. See the Remote Annex Administrator’s Guide
for UNIX for configuration information.

About this Guide

This guide includes the following chapters and appendices:

Chapter 1

Introduction
This chapter contains an overview of the Remote
Annex 2000; it describes the hardware features and
firmware functions.

Chapter 2

Installing the Remote Annex 2000
This chapter describes how to install the Remote
Annex 2000 on a LAN, and how to confirm its
operating status.

Chapter 3

ROM Monitor Commands
This chapter describes the ROM Monitor commands
that modify specific configuration parameters,
perform diagnostic tests, and load the
operational code.

Chapter 4

Troubleshooting Procedures
This chapter provides troubleshooting and
verification procedures.

Appendix A

Port Pin/Signal Allocations
This appendix details the connectors located on the
rear panel of the Remote Annex 2000.

Summary of Contents for Remote Annex 2000









































































































































Reviews:

No comments