Baumer EAL580 MT Series Manual Download Page 74

Page: 74 / 74

Baumer_EAx_PROFINET_EN_202011_MNL.docx

74/74

www.baumer.com

11.20

Appendix A

9.1. Software Change Log (from firmware V1.2.2 to V1.3.0)

The following table contains important changes of firmware version (V1.3.0 compared to V1.2.2).

Change

Description

[Reset via button]
With Ethernet connection possible

A reset via the button is now also possible if the
encoder has an Ethernet connect

ion (“link

established”). In V1.2.2 a reset via the button was
only possible when the encoder had no Ethernet
connection.

Details can be found here:

Push Button for Preset / Reset

[Reset via button]
Functionality extended

Additionally to resetting of IP settings and station
name the following actions are done in firmware
version 1.3.0:

reset of several encoder parameters
(details: see link below)

reset of the internal preset offset to 0

estart (“software reset”) of the encoder

Details can be found here:

Parameter reset using the optional push button

[Temperature]
Added

To provide a temperature value record 0x0005 was
added.

Details can be found here:

Vendor-specific parameters

[Operating hours counter]
Added

To provide an operating hours counter PNU
65001.7 is supported.

Details can be found here:

Parameter 65001: Operating status

[Baumer serial number]
Added

To provide the Baumer serial number record
0x0006 was added.

Details can be found here:

Vendor-specific parameters

[Preset offset]
Added

To provide the preset offset PNU 65001.8 is
supported.

Details can be found here:

Parameter 65001: Operating status

[Alarms]
Alarm code 0x0

224 (“Total measuring range

illegal

”)

Alarm with code 0x0224 is reported if the total
measuring range is set to 1.

[Alarms]
Alarm code 0x0

201 (“Preset out of range”)

Alarm with code 0x0201 is reported when an invalid
value is written into PNU 65000.

[Preset]
Set preset value (PNU 65000) directly in the
«module parameters»

The PLC writes PNU 65000 during startup of the
encoder.

To use this functionality the following GSDML file
has to be used:

„GSDML-V2.32-Baumer-EAx580_PN-20190715.xml“

Summary of Contents for EAL580 MT Series











































































Search results

Summary of Contents for EAL580 MT Series

Reviews:

Related manuals for EAL580 MT Series

Brands by name

Popular brands

Baumer EAL580 MT Series, Manual

Search results

Summary of Contents for EAL580 MT Series

Reviews:

Related manuals for EAL580 MT Series

Brands by name

Popular brands