Bauknecht BVH 92 2B K, Instructions For Use Manual

Page: 62 / 160

63
Press again to turn off
Note: This function has priority over the others.
Starting the extractor:
Touch (press) the Selection zone (12) to activate the
extractor
Extraction speed (power):
The extractor is equipped with 3 levels of extraction speed
(power)
Touch and slide your fingers along the Selection bar (3):
to the right to increase the level of power;
to the left to decrease the level of power.
The power level set will be displayed in the
Selection/Display area (12)
Power Booster
The product has 2 additional power levels (above level 3)
• Power Booster 1 : timed for 15 min.
• Power Booster 2 : timed for 5 min.
after which the power returns to the previously set level.
Touch and slide with the fingers along the Selection bar (3)
(over level 3) and activate the Power Booster 1
The Power Booster level 1 is indicated in the Selection /
Display area (12) with the number "4" flashing
Touch and slide with the fingers along the Selection bar (3)
(over level 3) and activate the Power Booster 2
The Power Booster level 2 is indicated in the Selection /
Display area (12) with the symbol” ” flashing
Automatic operation
The hood will turn on at the most suitable speed, adapting the
extraction capacity to the maximum cooking level used in the
cooking zone.
When the cooking zones are switched off, the hood adapts its
extraction speed, decreasing it gradually, to eliminate residual
vapours and odours.
To activate this function:
Press (14)
Repeat the operation to deactivate .
Note: if during automatic operation are selected from the
Selection bar (3) the speeds from 1 to 3 , the automatic
operation is interrupted;
if, instead, the Power Boosters are selected, automatic
operation will resume at the end of the timing, while in the
meantime the symbol “ ” remains flashing.
Note: if the hob automatically shuts down with Automatic
mode active, the extractor fan will automatically turn off in a
gradual manner.
Filter saturation indicator
The hood indicates when filter maintenance is needed:
Carbon/ceramic odour filters
“ ”( 13) comes on
Grease filter
“ ”( 13 ) flashes Note: this function is disabled by
default (see how to enable it in the paragraph "Activation
filter saturation indicator")
Reset filter saturation
After performing maintenance on the filters (greases and/or
carbon/ceramic), press and hold “ ” (13) ;
“ ” (13) turns off, restarting the indicator count.
Activation filter saturation indicator
This indicator is normally deactivated.
To activate it, proceed as follows:
• turn on the extractor hob via ;
• with the extraction motor and cooking zones off, press the
Selection zone (12)
• long press “ ” (11) until the letters “F” – “G” appear
alternately flashing in the Display (12)
F = carbon/ceramic odour filters
G = grease filter
Carbon/ceramic odour filters
.press on the Display (12) when the letter “ F ” appears
• press “ ” (13) – flashing light
• long press “ ” (11) again to confirm the activation
of the carbon/ceramic odour filter indicator
Grease filter
• press on the Display (12) when the letter “ G ” appears
• press “ ” (13) – fixed light
•long press “ ” (11) again to confirm activation of the
grease filter indicator
The device can also be used in combination with a
Window sensor KIT (not supplied by the manufacturer).
If the Window sensor KIT is installed (only in the case of use
in EXTRACTOR mode), air extraction will stop working each
time the window in the room, on which the KIT is applied, is
closed.
- The KIT must be electrically connected to the device
by qualified and specialised technical personnel.
- The KIT must be separately certified in accordance
with the safety standards relative to the component
and its use with the device. Installation must be
carried out in accordance with current regulations for
domestic systems.
CAUTION:
- the wiring of the KIT to be connected to the device
must be part of a certified safety extra low voltage
(SELV) circuit.
- the manufacturer of this device declines all liability
for any inconveniences, damage, fires caused by
defects and/or problems associated with malfunction
and/or incorrect installation of the KIT.