manualshive.com logo in svg

Baroness LM101, Owner'S Operating Manual, Page: 83 / 88

Share
Download
Baroness LM101 Owner'S Operating Manual Download Page 83

Uneven Blade Engagement

The unevenness is a difference of tightening
torque between the left and right cutter
adjustment nuts, or blade engagement on only
one side, which cannot be adjusted.
Promptly resolve the issue in order to maintain
the optimum performance of the machine.

Cause of unevenness

Measure to resolve

Asymmetrical wear of
reel cutter (cutting
cylinder)

Cylindrical grinding of
reel cutter (cutting
cylinder)
Replacement of reel
cutter (cutting cylinder)

Asymmetrical wear of
bed knife (bottom blade)

Surface grinding of bed
knife (bottom blade)
Replacement of bed
knife (bottom blade)

Distortion of frames

Rearrange frames in
parallel

Important

Depending on the extent of the symptoms,
they may not be resolved.

Important

Performing temporary measures may cause
the symptoms to progress, resulting in cutting
issues.

Temporary measures:

Adjustment with cam bushes
"Adjusting CAM" (Page 5-12)
Adjustment of spring pressure
"Adjustment of Cutter Adjustment Spring"
(Page 5-12)

･

･

Maintenance

LM101

Maintenance

Page 5-31

Troubleshooting Procedures of Aftercut Appearance

Summary of Contents for LM101

























































































Reviews:

No comments