manualshive.com logo in svg

Baroness LM101, Owner'S Operating Manual, Page: 40 / 88

Share
Download
Baroness LM101 Owner'S Operating Manual Download Page 40

Don't grip the main clutch lever.

1

2

B

A

k7k67l-004

Procedure to Start Engine_003

1

Main clutch lever

2

Clutch lock lever

A

ON

B

OFF

Set the fuel cock to the "Open" position.

A

1

B

B

v2e27i-055

Procedure to Start Engine_004

1

Fuel cock

A

Close

B

Open

Set the engine switch to the "ON" position.

B

A

1

v2e27i-043

Procedure to Start Engine_005

1

Engine switch

A

ON

B

OFF

3.

4.

5.

Set the choke lever to the "Close" position.

A

A

B

1

v2e27i-056

Procedure to Start Engine_006

1

Choke lever

A

Close

B

Open

Important

Return the starter grip slowly to its original
position after the engine starts.
Do not let go of the pulled starter grip since it
may cause damage to the machine.

Pull the starter grip swiftly, and the engine
will start.

1

2

v2e27i-070

Procedure to Start Engine_007

1

Starter grip

2

Recoil starter

6.

7.

LM101

Handling Instructions

Page 4-18

Procedure to Start/Stop Engine

Summary of Contents for LM101

























































































Reviews:

No comments