manualshive.com logo in svg

Baroness LM101, Owner'S Operating Manual, Page: 80 / 88

Share
Download
Baroness LM101 Owner'S Operating Manual Download Page 80

Troubleshooting Procedures of Aftercut

Appearance

Scalping

Is the roller bracket secured?

YES

NO

࣭

Tightening to secure

࣭

Replacement of securing screws

࣭

Replacement of front roller bearing

࣭

Replacement of front roller shaft

Have adjustments been made to obtain desired cutting height?

YES

YES

NO

Is there a proper balance between the bed knife (bottom 
blade) and cutting height?
(See "Cutting Height and Thickness of Bed Knife (Bottom Blade)".)

Adjustment of cutting height

Do the greens have large undulations?

࣭

Change of cutting height

࣭

Replacement of bed knife (bottom blade)

NO

YES

Are the greens matted?

NO

YES

࣭

Increasing of cutting height

࣭

࣭

Surface finishing of greens (compaction 
rolling, etc.)

࣭

Increasing of cutting height

࣭

Rehabilitation of greens (vertical cutting, etc.)

࣭

Application of topdressing sand

NO

YES

Are the greens sloped?

Change of cutting direction

Does the front roller rattle up and down?

NO

YES

Does the rear roller rattle up and down?

NO

YES

࣭

Replacement of rear roller bearing

࣭

Replacement of rear roller

YES

Is the surface of the greens finished?

࣭

Increasing of cutting height

NO

If the groomer is installed: Remove the 
groomer, replace the roller bracket with 
the L-shaped bracket, and then bring 
the front roller closer to the reel cutter 
(cutting cylinder).

iuwt3m-002E

Scalping_001

Angled Mismatch

Is the cutting height on both sides adjusted to be the same?

Is the bed knife (bottom blade) chipped?

Does the front roller rattle up and down?

Adjustment of cutting height

YES

NO

NO

YES

࣭

Replacement of bed knife (bottom blade)

Does the rear roller rattle up and down?

NO

YES

࣭

Replacement of front roller bearing

࣭

Replacement of front roller shaft

NO

YES

Are the greens matted?

NO

YES

࣭

Replacement of rear roller bearing

࣭

Replacement of rear roller

࣭

Rehabilitation of greens
 (vertical cutting, etc.)

NO

YES

Do the greens have large undulations?

NO

YES

Are the greens sloped?

Change of cutting direction

YES

Are the left frame and right frame distorted?

Contact your sales representative or dealer.

If the groomer is installed: Remove the 
groomer, replace the roller bracket with 
the L-shaped bracket, and then bring the 
front roller closer to the reel cutter 
(cutting cylinder).

7x9s4e-002E

Angled Mismatch_001

LM101

Maintenance

Page 5-28

Troubleshooting Procedures of Aftercut Appearance

Summary of Contents for LM101

























































































Reviews:

No comments