background image

Manual 2100-592C
Page 

20 of 69

Electrical Grounding

When installed, the furnace must be electrically 
grounded in accordance with local codes or in the 
absence of local codes, with the National Electrical 
Code, ANSI/NFPA 70, or Canadian Electrical Code, 
CSA22.1, latest edition.  Use a copper wire from green 
ground wire on the furnace to a grounded connection 
in the service panel or a properly driven and electrically 
grounded ground rod.  See Table 1 for proper ground 
wire size.

Field-Installed Equipment

Wiring to be done in the field between the furnace 
and devices not attached to the furnace, or between 
separate devises which are field installed and located, 
shall conform with the temperature limitation for 
Type T wire {63° F rise (36° C)} when installed in 
accordance with the manufacturer’s instructions.

Installation of Flexible Conduit Through Return Air 

Opening

NOTE:  To allow proper clearance between the control 

panel and any vent options, 90° conduit 

fittings must be used on the back of the 

control panel.

Installing Conduit

 (See Figure 10)

1.  Remove conduit access panel if required to gain 

access to area behind control panel.

2.  Remove low voltage and high voltage knockouts 

located in rear of control panel.

3.  Run low voltage conduit through 7/8 bushing 

located in conduit entrance plate and secure to low 
voltage opening in rear of control panel.

4.  Run high voltage conduit through 1-3/4 bushing 

located in conduit entrance plate and secure to 
high voltage opening in rear of control panel.

5.  Replace conduit access panel if required to 

complete installation.

6.  Seal around conduit in conduit entrance plate.

        WARNING

Failure to provide a proper electrical ground 

could result in electric shock or fire.

15.  WIRING – MAIN POWER

Refer to unit rating plate for wire sizing information and 
maximum fuse or circuit breaker size.  Each outdoor 
unit is marked with a “Minimum Circuit Ampacity”.  
This means that the field wiring used must be sized to 
carry that amount of current.  All models are suitable 
only for connection with copper wire.  Each unit and/or 
wiring diagram will be marked “

Use Copper Conductors 

Only

”.  These instructions 

must be 

adhered to.  Refer 

to the National Electrical Code (NEC) for complete 
current carrying capacity data on the various insulation 
grades of wiring material.  All wiring must conform to 
NEC and all local codes.

The electrical data lists fuse and wire sizes (75° C 
copper) for all models.

The unit rating plate lists a “Maximum Time Delay 
Relay Fuse” or circuit breaker that is to be used with 
the equipment.  The correct size must be used for 
proper circuit protection and also to assure that there 
will be no nuisance tripping due to the momentary high 
starting current of the compressor motor.

The disconnect access door on this unit may be locked 
to prevent unauthorized access to the disconnect.  To 
convert for the locking capability, bend the tab located 
in the bottom left hand corner of the disconnect 
opening under the disconnect access panel straight 
out.  This tab will now line up with the slot in the door.  
When shut, a padlock may be placed through the hole 
in the tab preventing entry.  

See “Start Up” section for important information on 
three phase scroll compressor start ups.

        WARNING

For personal safety, turn off electric power 

at service entrance panel before making any 

electrical connections.  Failure to do so could 

result in electric shock or fire.

        WARNING

Failure to provide an electrical power supply 

shut off means could result in electric shock or 

fire.

Summary of Contents for W24G2DA






































































Reviews: