![background image](http://html1.mh-extra.com/html/barco/imagetile/imagetile_system-manual_3985240074.webp)
System manual ImageTile
75
Installing the Driver Using the Windows XP Found New
Hardware Wizard
SPECIAL NOTE: Prior to installing the BarcoMed drivers you MUST
install the BarcoMed Imaging Board(s), connect the ImageTile display
panel(s) to the card(s), and turn the ImageTile display on. Refer to
the Hardware Installation section of this manual for instructions on
installing the BarcoMed Imaging Board(s) and connecting them to the
ImageTile display panel(s).
The following driver installation instructions presume that Windows XP
is already installed on your system. If you need to install or reinstall
Windows XP on your system you must first remove the BarcoMed
Imaging Boards and use a 3
rd
party VGA card and VGA monitor during
the Windows XP installation process.
To install the BarcoMed 3MP2FH Windows Display Driver for the first
time follow the steps below, if you are reinstalling the drivers or
installing a new driver release skip to the next section:
1. Install the BarcoMed 3MP2FH Imaging Board(s) into your machine.
Please refer to the hardware installation section for more
information.
2. Boot the machine and log on using an account with administrative
privileges.
3. Windows XP will do a thorough inspection of your system and will
announce that it has found new hardware. This may take several
minutes. Please be patient.
4. Close any informational balloons that Windows XP may open in
the lower right hand corner of the monitor.
5. Windows XP will automatically launch the “Found New Hardware
Wizard”.
6. Insert the BarcoMed software CD into your computer’s CD drive.
Select the radio button beside “Install the software automatically
(Recommended)”. Click “Next”.
7. Windows XP will now search the computer and CD for the correct
driver. When Windows XP has found the BarcoMed 3MP2FH
driver it will warn you that the software “has not passed Windows
Logo testing to verify its compatibility with Windows XP.” Click
“Continue Anyway” to install the drivers.
8. When Windows XP has finished installing the drivers, click
“Finish” on the “Found New Hardware Wizard”.
If you are installing more than one BarcoMed 3MP2FH board in your
system, Windows will again do a thorough inspection of your system
and automatically detect them and again launch the found New
Hardware Wizard for each board installed. Repeat steps 6 through 8
BarcoMed software driver installation
Summary of Contents for IMAGETILE
