Connections
6-4
5976066 BARCOCINE 8 10022000
Connecting a RGB Analog source to port 3
Connect your RGB source via an interface to Port 3.
Note :
If a line doubler or line multiplier is built in, the default position of this line doubler (multiplier) soft option is ON (active). The video input
signal will be displayed as a non interlaced image (= improved image stability).
To enable or to disable this function, enter the adjustment mode and change the position of the ON/OFF toggle switch (see chapter
'Random access' adjustment mode).
Always use an interface when a computer and local monitor have to be connected to the projector.
BARCO's Interface units.
Universal analog interface
R9826100
RGB 120 MHz Analog Interface
R9826570 (230V)
Multifunctional Analog Interface Kit
R9828120 (230V)
(MAGIK)
R9828129 (120V)
VGA interface
R9828070 (230V)
R9828079 (120V)
MAC interface
R9828050 (230V)
R9828059 (120V)
21
2))
P OWER / MA INS
SHULSKH UDOV
5
*
%
&RPS+6\QF 96\QF
COMM. PO RT
P ORT 3
PO RT 4/5
9QRP
,QRP
)UHT
6H HLQVWDOODWLRQLQV WUXFW LRQVEH IRUHFRQQHFWLQJWRWKH V XSSO\
9RLUODQRWLFHGLQVWDOODWLRQDYDQWGHU DFFRUGHUDXU pVHDX
9
$PS
+]
69,'(2
2 )) 21
2KP
9,'(2
JUHHQRSHUDWLRQ
UHGVWDQGE\
PO RT 2
P ORT 1
2 ))21
2 KP
P ROJE CTOR MODE
7KLVGHYLFHF RPSOLHVZ LWKSD UWRI
WKH)&&UXOHV2SHU DWLRQLVVXEMHFWWR
IROORZ LQJWZ RF RQGLWLRQV 7KLV
GHYLFH PD \QRWFDXVHKDUPIXOLQWHU
IH UH QFH DQG WKLVGHYLFH PXV W
DFF HSWDQ\ LQWH UIHUHQF HUH FHLYHG
LQFOXGLQJLQWHUIHUHQF HWKDWPD \FDXV H
XQGHVLUHGRSHUDWLRQ
,1 3
,1 3
5
*
%
+
9
,1 387
$1$/2*,17(5) 0+]
21
2))
LQYHU
RK P WHUP
Pin configuration D9 connector of the Analog input.
1
Not connected
2
Ground RGBS
3
RED
4
GREEN
5
BLUE
6
Ground RGBS
7
Ground RGBS
8
Hor/comp. sync
9
Vert. sync
Input selection
With the RCU or built-in RCU : press digit button 3
Locations of the Termination Resistors and Switches on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the projector and unplug the power cord from the wall outlet.
75
W
Termination resistors
In case of chaining (loop-through) the projectors, the 75
W
line termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.