background image

USE  AND  CARE  INSTRUCTIONS

29

5.

8.

7.

9.

6.

Set Control Knobs to OFF and open the LP Gas tank valve

SLOWLY 1/4 of a turn

.  For Natural Gas open the Shut Off

Valve  at  source.

Push and turn Right Main Burner Control Knob to HI/  .
You will hear a clicking sound as the burner is being ignited.
Always light  the RIGHT  Main Burner  first.

If  ignition  does  not  occur  in  5  seconds,  turn  the  Burner
Control(s)  off,  wait  5  minutes,  and  repeat  the  lighting
procedure.  If  ignition  still  does  not  occur,  turn  the  burner
control(s) and gas source OFF. Wait 5 minutes for gas to
clear and then conduct a leak test of ALL gas connections
and gas sources as explained in the Use and Care section
of this manual. If no leaks are detected, wait 5 minutes for
any  gas  to  clear  and  repeat  the  lighting  procedure.

After one Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn.

Turn each other burner knob to HI/    to light. Note: When
lighting  all  main  burners,  start  with  the  burner  furthest
from  fuel  source  location,  then  light  remaining  burners  in
sequence  moving  toward  fuel  source.

Failure  to  replace  a  faulty  hose,  secure  gas  supply
connections  or  to  open  the  Lid  before  proceeding  to
the  Lighting  Procedures  could  result  in  a  fire  or
explosion  that  could  cause  serious  bodily  injury,
death,  or  property  damage.

    WARNING

!

!

Grill Lighting Instructions

1.

Main  Burner

(for  B3812ALP/NG  & B3812BLP/NG  Models)

Rotisserie
Burner

Infrared
Burner

Open  LP  Gas  tank

OFF

HI/

LO

(for  BAI12ALP/NG & BAI12BLP/NG  Models)

Infrared
Burner

Main  Burner

Rotisserie
Burner

Rotisserie
Burner

Rotisserie  Burner  Lighting  Instructions

Follow steps 1 through 5 of the Grill Lighting Instruc-
tions.

Push and turn Control Knob to HI/   and hold knob in.

Keep  pressing  and  hold  in  5  -  10  seconds  before
releasing.

If ignition does not occur in 5 seconds, turn the Burner
Control(s)  off, wait  5  minutes,  and repeat  the  lighting
procedure.  If  ignition  still  does  not  occur,  turn  the
burner control(s) and gas source OFF. Wait 5 minutes
for gas to clear and then conduct a leak test of ALL gas
connections and gas sources as explained in the Use
and  Care  section  of  this  manual.  If  no  leaks  are
detected,  wait  5  minutes  for  any  gas  to  clear  and
repeat  the  lighting  procedure.

After Burner is lit, turn the tank valve SLOWLY one more
1/4 of a turn.

IMPORTANT: 

 Do not use the Rotisserie Burner and Main

Burners  at  the  same  time.  Rotisserie  burner  is  for  Rotis-
serie  Cooking  only.

1.

2.

4.

3.

5.

HI/

OFF

Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions. If a hose is damaged in any way, do
not  use  your  grill  before  replacing  the  hose  with  an
authorized  part  from  the  Parts  List.  Also  make  sure  all
gas  supply  connections  are  securely  tightened.
Familiarize  yourself  with  all  Safety  and  Use  and  Care
instructions  in  this  manual.  Do  not  smoke  while
lighting  your  grill  or  when  checking  the  gas  supply
connections.
Be  sure  that  the  LP  Gas  tank  is  filled,  and  lock
Casters  (if  the  grill  is  a  cart  model)  to  prevent
movement  during  grill  operation.
Open  the  Grill  Lid.

4.

3.

2.

OFF

LO

HI/

Summary of Contents for B3812ALP













































Reviews: