background image

A-3

Guide  to  Searing  using  the  Infrared  Cooking  Zone

Searing Steak and Ribs

Turn  the  Infrared  Burner  on  HI  and  preheat  for  10  to  15
minutes  with  the  Lid  open.  Then  place  the  meat  on  the
Cooking  Grid  and  sear  each  side  for  approximately  2  min-
utes. Reduce the Infrared Burner to LOW or move meat to the
primary  grilling  area  and  finish  cooking.  Grilling  times  will
vary  according  to  meat  thickness.

Searing Hamburgers and Sausages

Turn  the  Infrared  Burner  on  HI  and  preheat  for  10  to  15
minutes  with  the  Lid  open.  Then  place  the  meat  on  the
Cooking  Grid  and  sear  each  side  for  approximately  2  min-
utes. Reduce the Infrared Burner to LOW or move food to the
primary  grilling  area  and  finish  cooking.  Grilling  times  will
vary  according  to  meat  thickness.

Hamburgers  and  sausages  are  fatty  so  you  should  expect
some  flare-ups  when  cooking  these  foods.  To  minimize
flare-ups  follow  the  instructions  on  page  A-1.  You  may  also
consider grilling these and other fatty foods using the primary
grill  area  and  the  indirect  cooking  method.

Cut of Meat

T-bone  steak
Sirloin  steak
Beef  spare  ribs
Porterhouse    steak
New  York  strip  steak

Hamburgers
Sausages

Approximate Total Cooking
Time

Rare: 

4  minutes

Medium:

  6-7  minutes

Well done:

 8-10  minutes

Rare: 

4  minutes

Medium:

  5  minutes

Well done:

 6-7 minutes

Important notes about using the Infrared Burner

Whether  you  are  a  seasoned  chef  or  a  newcomer  to  gas
grilling,  infrared cooking  is  quite different  than  grilling over  a
traditional burner. Although the primary grill burners will also
sear meat, the Infrared Burner produces a more intense and
concentrated  heat  that  sears  the  meat  more  quickly.  This
quick searing produces  a crisp and flavorful  outer crust and
locks  in  the  meat's  natural  flavor  and  juices.

Follow  the  cooking  guidelines  provided.  Then  take  some
time to experiment with your Infrared cooking zone. Also, read
the Cooking Instructions on page A-1 so you understand the
importance of pre-heating, cooking  temperatures and safety
warnings.

Once lit, leave the Infrared Burner on High and sear both
sides  of  meat  using  the  guidelines  below.

Once  seared,  adjust  the  Infrared  Burner  to  Low  and
continue  cooking  until  desired  doneness.  You  can  also
move the seared meat to the primary grilling area to finish
cooking.  This  method  allows  you  to  sear  and  prepare
larger  amounts  of  meat.

NEVER attempt to douse a flare-up with water which can
damage  the  Burner.  To  control  flare-ups:

The  Lid  must  always  be  open  when  the  Infrared  Burner
is  lit.

Infrared  cooking  times  will  be  much  shorter  than  tradi-
tional  grilling  so  do  not  leave  the  grill  unattended.

Trim  excess  fat  from  meats  and  poultry.

Preheat  the  Burner  properly.

Clean the Burner regularly to remove food and grease
build-up.  See  Burner  Tube  cleaning  instructions  in
this  manual.

Reposition  your  food  often  and  consider  moving  the
seared  meat  to  the  primary  grilling  area  to  finish
cooking

.


Fis h

145ºF/63ºC

Pork

160ºF/71ºC

Egg Dishes

160ºF/71ºC

Steaks  and Roas ts of Beef, Veal or 
Lamb

145ºF/63ºC

Ground Beef, Veal or Lamb

160ºF/71ºC

Whole Poultry (Turkey, Chicken, 
Duck, etc.)

165ºF/74ºC

Pieces  of Poultry (Chicken Breas t, 
etc.)

165ºF/74ºC

Safe Minimum Internal Tem peratures

Summary of Contents for B3812ALP













































Reviews: