24
Copyright 3/20
Bandit
MODEL 1425
1. Hydraulic oil:
Change hydraulic oil and flush the hydraulic reservoir
tank.
2. Hydraulic suction screen(s):
Change hydraulic suction screen(s) yearly or every
2000 hours.
3. Fuel tank:
Drain and clean the fuel tank yearly.
4. On machines built before 4/20, remove old
grease from drum head bearings and repack with
new grease:
Disassemble the drum head bearings, remove all
grease from the bearing housing, repack the bearing
with new grease, fill the housing 1/2 of the way and
reassemble the bearing, once a year with EP-2
Lithium type grease. See page 42.
YEARLY MAINTENANCE
MAINTENANCE
BOLT TORQUE CHART
(THESE TORQUES ARE BASED ON DRY, CLEAN THREADS)
DESCRIPTION
BOLT SIZE TORQUE (FT.-LBS.) TORQUE (Nm)
Cutterhead Bearing Bolts
3/4” - 10 NC
220
298
Cutterhead Shaft Bushing “4040”
3/4” - 10 NC
142
193
Anvil
3/4” - 10 NC
375
508
Cutter Tooth Bolts
3/4” - 10 NC
375
508
Raker Bolts
3/4” - 16 NF
375
508
Cutterbody Holder Bolts
1” - 14 NS
700
949
Wiper Insert Bolts
5/8” - 11 NC
160
217
Beast Knife Bolt
3/4” - 16 NF
420
569
Feedwheel / Conveyor Bearing Bolts
5/8” - 11 NC
75
102
Feedwheel / Conveyor Bearing Set Screws
3/8” - 24 NF
20
27
Discharge Idler Roller Bushings
7/16” - 14 NC
46
62
Grip-Tight Feedwheel / Conveyor Bearing Set Screws
2
3
“TG” Hydraulic Motor Shaft Nut
1” - 20 NEF
250 - 300
339 - 407
Discharge Motor Coupler
5/8” - 18 NF
250
339
Engine Hold Downs
5/8” - 11 NC
125
169
Engine Sheave Bushing “E”
1/2” - 13 NC
60
81
Chipper Sheave Bushing “J”
5/8” - 11 NC
135
183
Feedwheel Motor Sprocket Bushing “Q1”
3/8” - 16 NC
29
39
Feedwheel Sprocket Bushing “R1”
3/8” - 16 NC
29
39
Hitch Mount Bolts
5/8” - 11 NC
220
298
Before tightening bolts be sure you have the correct size bolt for the correct amount of torque.
Use only factory approved knives and hardware.
BASIC WHEEL TORQUE REQUIREMENTS (per mfg.)
Keep lug nuts properly tightened, check new unit before operation, after the first 10, 25, and again
at 50 miles. Check the torque weekly.
DESCRIPTION
BOLT SIZE
TORQUE (FT.-LBS.) TORQUE (Nm)
5 & 6 Lug hubs
1/2” - 20 Studs
90 - 120
122 - 163
8 Lug Hubs
1/2” - 20 Studs
90 - 120
122 - 163
8 Lug Hubs
9/16” - 18 Studs
140 - 170
149 - 163
8 Lug Hubs (Cone Nut)
5/8” - 18 Studs
190 - 210
258 - 285
8 Lug Hubs (Flange Nut)
5/8” - 18 Studs
275 - 325
373 - 441
8 Lug Hubs (Flange Nut)
22 mm x 1.5 Studs
450 - 500
610 - 678
10 Lug Hubs
22 mm x 1.5 Studs
450 - 500
610 - 678
10 Lug Hubs
3/4” - 16 Studs
450 - 500
610 - 678
10 Lug Hubs
1 1/8” - 16 Studs
450 - 500
610 - 678
(Consult axle manufacturers manual shipped with each machine for specific axle-stud-wheel combination
lug nut torques.)
