background image

Appendix B

Appendix B-1

MN1269

Jumper and Personality Module Settings

Personality Module Current Settings  Refer to Figure B-1.

The personality module allows you to calibrate the servo control.  Resistors can be
soldered to the module to select the upper limit values of the following:

Peak Current
Continuous Current
Foldback Current  (LD3015HS)

Peak and Continuous Current Levels

Adding a resistor reduces the set values from the specifications in Section 1.

Figure B-1  

R96

C25

R97

C26

R98

C27

Foldback Current Level (LD 3015HS)

Foldback Current

(Amps)

Feedback Resistance

(Ohms)

5

453

7

715

9

1.0K

11

1.37K

13

1.82K

15

2.43K

Peak / Continuous Current Levels

Peak

Continuous

Ipeak (Amps)

RP (Ohms)

I rms (Amps)

RR (Ohms)

30

OPEN

15

OPEN

28

14.0k

14

475k

26

8.87k

13

97.6k

24

6.19k

12

59.0k

22

4.64k

11

31.6k

20

3.57k

10

23.2k

18

2.74k

9

16.2k

16

2.15k

8

11.3k

Servo Systems Co. • 115 Main Road • P.O. Box 97 • Montville, NJ, 07045-0097 

(973) 335-1007 • Toll Free: (800) 922-1103 • Fax: (973) 335-1661 

www.servosystems.com

Summary of Contents for LD Series






































Reviews: