background image

Appendix A

Appendix A-1

MN1269

Condensed Installation Instructions

Step 1
Become familiar with the equipment.  You should have:

1.

Servo Control Cards of the type and quantity you have ordered, mounted to the
chassis.

2.

Chassis Assembly which also includes:
– Logic power supply (bias supply)
– Overvoltage protector (shunt regulator)
– Bus power supply

In addition to the above you will find an Installation and Operating Manual and input
connector which are attached to the servo control cards.

Step 2
Read the Installation and Operating Manual.
It contains detailed installation and start up procedures and drawings pertaining to your
equipment.  Specific CAUTIONS must be adhered to so that equipment or personnel are
not damaged or injured.

Step 3
Mount the Chassis Assembly.

 WARNING: Do not apply power until all connections are made, connections are

checked and the safety precautions in Sections 1 are read and
understood.

Step 4
Connect the Motors.

1.

Connect motor armature leads to the motor output terminals on the chassis
assembly.  Refer to Figure A-1.

2.

Connect the tachometer leads to the input connector A1, pins 5 and 6. See
input connector Installation Drawing.  Be sure that the armature and tach are
connected to the same axis.

Step 5
Connect Power to the Chassis Assembly.

Connect the power source to the input terminals.  Use caution when connecting 115VAC
to LD-2 (one input power units) and LD-4 (two input power units).  Refer to Figure A-1.

Step 6
Refer to Section 3 for Start Up and Adjustment instructions.

Servo Systems Co. • 115 Main Road • P.O. Box 97 • Montville, NJ, 07045-0097 

(973) 335-1007 • Toll Free: (800) 922-1103 • Fax: (973) 335-1661 

www.servosystems.com

Summary of Contents for LD Series






































Reviews: