Document: 333D012G
5-18-2007
- 47 -
Channel Stand Installation or Removal Procedure
To install a stand, follow steps (1-7). To remove a stand, reverse steps (1-7)
1)
First gather all stand components and attaching hardware. The stand parts consist of two sides and one
back support. Hardware consist of (4) 1/4"x 1-1/4" bolts w/ 1/4" flat/lock washers and 1/4" hex nuts, (4)
3/8" x 1 bolts w/ 3/8" flat/lock washers, (8) chrome dots, (4) Adjustable leg levelers. Tools required are a
7/16” wrench or deep socket, 9/16” wrench or socket.
2)
Place stand sides on the floor so that the stainless steel legs are setting on the floor. Next place the stand
back support between the sides so that the open part of the channel is towards the floor. This can also be
done by rotating the stand parts (360 degrees), to make attaching the hardware easier.
3)
Using the 3/8 hardware, attach the sides and back support by inserting the bolts thru the (4) holes
located in the support into the already installed rivnuts in the two sides. (2) bolts each side. Do not
tighten any of these bolts until you have all (4) of them threaded in slightly. Tighten bolts after this is
done.
4)
With stand assembly complete, rotate stand so that the back of the sides are setting flat on the floor.
Attach the leg levelers by screwing them into the bottom of the stainless steel legs in the sides of stand
assembly. Position the stand assembly in the upright position so that the leg levelers are now resting on
the floor. The stainless steel legs can be adjusted to your desired height requirement. This is done by
removing and replacing the (2) 3/8"bolts in each leg. Unused rivnuts in the legs will be plugged with the
(8) chrome dots. If the cabinet is not in its permanent location you may want to perform the leg
adjustment after step 7.
5)
Lift the cabinet high enough to allow clearance for the stand assembly to be positioned under it. Lifting
is typically done from the front of the cabinet. The stand assembly is slid in from the back of the cabinet.
If space constraints are an issue, the stand may have to be assembled under the cabinet after it has been
lifted.
6)
Once the stand is positioned under the cabinet, install (4) 1/4"x 1-1/4" bolts into the key way slots
located under the cabinet in each of the (4) corners. The cabinet is now ready to be lowered onto the
stand. There are (4) holes on the top of the stand which the 1/4"x1-1/4" bolts must be guided thru. Be
careful not to let the bolts drag thru the holes while lowering as burrs may occur and cause cross
threading. With the cabinet resting on top of the stand assembly, place (1) 1/4" flat / lock washer / hex
nut onto each of the 1/4x1-1/4" bolts. Tighten after all (4) are threaded on.
7)
Lift device should be removed if not being used to move cabinet into position. If lift device is mobile it
may be used to maneuver cabinet into desired location. A blanket could also be placed under the leg
levelers while sliding the unit to avoid scuffing the flooring.
Summary of Contents for SterilGARD III Advance
