Azbil MVC10A User Manual Download Page 50

Page: 50 / 64

Maintenance and troubleshooting of this instrument

Azbil Corporation

5-2

Model: MVC10A/10F - Multivariable Air Flow Meter

5-1:

Maintenance

Disassembling and assembling

Disassembling

Disassembling of the converter (See Figures 1-4 and 1-5.)

CAUTION

•

When opening or closing the cover for the converter, pay adequate attention not to allow dust and

rainwater to enter the inside of this instrument.

WARNING

• Before opening the cover, not only for disassembling, but also for any other purposes, be sure to

turn off the power. Otherwise an electric shock may result.

•

Whenever the system is energized, never perform wiring work. Otherwise an electric shock may

result.

Removing the cover

The cover is fixed with M4 screws. Loosen them with a Philip's or flat head

screwdriver, and then remove the cover.

Removing the cover for power supply unit

A cable is fed through the gap in the power unit cover and connected to the LCD

board. First remove the connector. The power unit cover is fixed to the case with M3

screws, each with a Philip’s head, at two spots, which should be removed.

Removing the terminal board and main board

The terminal board is fixed to the case with M3 screws, each with a Philip's head, at

four spots.

After removing the terminal board, you will find the main board, which is fixed to the

case with M3 screws, each with a Philip’s head, at two spots. Before removing them,

conduct the static charge removal operation.

Exercise care in this operation not to damage the cable connection of the detector

body and FPC.

CAUTION

• Before and after the removal of the terminal board and main board, be sure to perform the static

charge removal procedure. Otherwise, the performance of the system may be affected.

Assembling the converter

Use the steps for disassembling the converter in the reverse order for the assembling.

When fixing the terminal with screws, pay attention to avoid excessive screw

tightening that may damage them. Also take necessary care not to pinch the cable

connecting the FPC and LCD with screws or the cover.

Summary of Contents for MVC10A

































































Search results

Summary of Contents for MVC10A

Reviews:

Related manuals for MVC10A

Brands by name

Popular brands

Azbil MVC10A, User Manual

Search results

Summary of Contents for MVC10A

Reviews:

Related manuals for MVC10A

Brands by name

Popular brands