Axis 14363 User Manual Download | Manualshive

Page: 11 / 95

background image

Section 1: General Information

AXIS AFP IOP User’s Manual

7

Section 1

General Information

Product Overview

• This interface has full support for the IPDS features of the correspond-

ing IBM 3812, IBM 3816 and IBM 4028 printers and is 100% plug
compatible with these printer types.

• Emulation selection (3812/16 or 4028) is easily done from the front

panel control.

• Hardware installation is easily done by the user. The only tool needed

is a screwdriver for mounting one single screw. The interface consists
only of two parts: -The AFP IOP main board and the externally
attached Twinax or Coax patch cable. The interface only takes posses-
sion of the internal optional port of the printer and allows dynamic
sharing with the existing input ports of the printer.

• The interface connects to the IOP input port of the Lexmark printer

allowing maximum utilization of the performance of the high speed
RISC processor on the AFP IOP interface.

• Best performance is obtained by using the Lexmark Optra series, which

is built around a new Graphics Engine based on an object oriented
design. The AXIS AFP IOP creates an HP PCL5 raster image for each
page to ensure 100% compatibility with the AFP architecture, and the
new Graphics enterpreter of the Lexmark Plus series can maintain full
printspeed during processing of complex graphics jobs.

«
...
9
10
11
12
13
...
»

Summary of Contents for 14363
































































































Reviews:

No comments

Related manuals for 14363

Brand: Olivetti Pages: 39

Brand: Labau Pages: 19

Brand: Pacbrake Pages: 9

Brand: PAJ Pages: 95

Brand: iDataLink Pages: 30

Brand: Xerox Pages: 414

Oakville Series

Brand: Napoleon Pages: 72

Brand: Napoleon Pages: 4

Allure Vertical Series

Brand: Napoleon Pages: 120

Brand: Panasonic Pages: 242

Brand: Omron Pages: 16

2 SD Card Memory Module NI 9802

Brand: National Instruments Pages: 16

Brand: TBC Pages: 12

Brand: Sirius Satellite Radio Pages: 8

Brand: Datasensor Pages: 2

Brand: Tobii Pro Pages: 34

Walimex Pro Operator

Brand: walser Pages: 24

PowerStation Plus

Brand: Mophie Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands