Axis 14363 User Manual Download | Manualshive

Page: 2 / 95

background image

ii

AXIS AFP IOP User’s Manual

About this manual

This manual will guide you through a simple step-by-step installation and
setup procedure. It is divided into six sections:

General

Information

About the AXIS AFP IOP Printer Interface, how it works, where to use it,
and its main features.

Front Panel

Operation

How to operate the Lexmark printer’s front panel when the AXIS AFP
IOP is installed.

Utility Program

The tool for reconfiguring and upgrading the software in the AXIS AFP
IOP.

Configuration

Parameters

A complete listing of the parameters available for configuration of the
AXIS AFP IOP.

Download/Upload

Downloading the configuration program and the fonts to the AXIS AFP
IOP, as well as uploading the current configuration.

Program Setup

Setup of the Utility Program output function.

The manual applies to the AXIS AFP IOP with firmware release 1.00 and
subsequent releases until otherwise notified.

This manual primarily describes operation of the AXIS AFP IOP installed
in Lexmark Optra series of printers. The AXIS AFP IOP also supports
Lexmark 4039 and 4039

Plus

series of printers, with some minor

differencies in the front panel operation.

Every care has been taken in the preparation of this manual; if you detect
any inaccuracies or omissions, please inform us at the address on the back
cover. Axis Communications AB cannot be held responsible for any
technical or typographical errors and reserves the right to make changes to
the product and manuals without prior notice.

«
1
2
3
4
...
»

Summary of Contents for 14363
































































































Reviews:

No comments

Related manuals for 14363

Brand: UFESA Pages: 27

Brand: Davis Instruments Pages: 16

Brand: Saxxot Pages: 13

Brand: Panasonic Pages: 268

Brand: Oki Pages: 17

Brand: Oki Pages: 12

Brand: Oki Pages: 30

Brand: Oki Pages: 391

Brand: Camoplast Pages: 60

Brand: Dascom Pages: 12

Brand: Dascom Pages: 19

Brand: Dascom Pages: 5

Brand: Panduit Pages: 74

Brand: Tally Pages: 2

Brand: Tally Dascom Pages: 57

Brand: Fenix Pages: 65

Brand: T-up Pages: 14

Brand: Varta Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands