manualshive.com logo in svg

AWH Tanko RT, Operating & Installation Instructions Manual, Page: 47 / 132

Share
Download
AWH Tanko RT Operating & Installation Instructions Manual Download Page 47

ATEX Retractor System TANKO-RT/-RTS 

 

 

3 Design and Function 

Translation - Operating/installation instructions 2020/01 

37/121 

 

Technical Data for Pneumatic Side 

Designation 

Retractor system TANKO-RT/RTS 

Actuator: 

Pneumatic (compressed air) 

Drive medium: 

Dry, oil-free compressed air (if necessary, install corresponding 
upstream maintenance unit) 

Operating pressure 

– 

Range 

– 

Recommended 

 
min. 5 bar (72.5 psi g) – max. 6 bar (87 psi g) 
6 bar (87 psi g) 

Connection: 

– 

Power cylinder 
 
 

– 

Locking cylinder 

 
Internal thread G 1/8 ISO 228-1 
throttle check valve for hose external Ø = 6 mm 
 
Internal thread M5 metric ISO thread 
Angled connector for hose external Ø = 6 mm 

Table 3.3-2: Operating Parameter, Pneumatic Side  

Power Supply, Limit Switch 

The power supply for the 5 limit switches (on the power and locking cylinder) is provided by approved 
switch amplifiers (8.2 V). 

The entire system for monitoring the position of the retracted or “retracted” power cylinder (two limit 
switches, G1 and G2) must comply with at least the ignition protection system b2, EN ISO 80079-37 in 
the currently applicable version. 

The entire system for monitoring the position of the locking cylinder (limit switches J and K) must 
comply with at least the ignition protection system b1, EN ISO 80079-37 in the currently applicable 
version. 

 

Recommendation:  
Switch amplifier (2-channel) with ATEX-approval for Zone 1 of Hans Turck GmbH & Co. KG. 
More detailed data can be found in the external data sheets or the manufacturer's operating 
instructions. 

Power Supply and Evaluation of Resistance Thermometer 

The power supply for the resistance thermometer (on the power cylinder) is performed via an approved 
supply isolator. 

The entire temperature monitoring system near the limit switch “F” must comply with the ignition 
protection system b1, EN ISO 80079-37 in the currently applicable version. 

 

Recommendation:  
Intrinsically safe supply isolator type IS Barrier, transmitter T15; T32xS, T53 with appropriate 
approval from WIKA Alexander Wiegand SE & Co. KG.  
More detailed data can be found in the external data sheets or the manufacturer's operating 
instructions. 

 

Summary of Contents for Tanko RT





































































































































Reviews:

No comments