Avnet UltraZed-EG Hardware User'S Manual Download Page 14 | Manualshive

Page: 14 / 47

background image

Version 1.0

Page 14

2.5 10/100/1000 Ethernet PHY

The UltraZed-EG SOM provides a single 10/100/1000 Ethernet port. The Zynq Ult MPSoC contains
hardened PS Gigabit Ethernet MAC (GEM) controllers. The UltraZed-EG SOM takes advantage of one of
the available PS GEM controllers to provide RGMII Ethernet signalling to the JX3 connector. The

Texas

Instruments DP83867

device is used to implement this interface. The 10/100/1000 Ethernet PHY connect

to the Zynq Ult MPSoC device through Bank 502.

The physical RJ45 connector and magnetics is not populated on the UltraZed-EG SOM. The SOM is
designed to have the physical RJ45 connector and magnetics reside on the end-user carrier card. The
RJ45 connector signals are connected to the JX3 Micro Header. The table below shows the connections
of these signals to the JX3 Micro Header.

Table 7

– 10/100/1000 Ethernet JX3 Pin Assignments

Signal Name

JX3 Pin

ETH_MD1_P

57

ETH_MD1_N

59

ETH_MD2_P

56

ETH_MD2_N

58

ETH_MD3_P

63

ETH_MD3_N

65

ETH_MD4_P

62

ETH_MD4_N

64

ETH_PHY_LED0

53

ETH_PHY_LED1

52

The next table shows the pin assignments to Bank 502 of the Zynq Ult MPSoC device for the
10/100/1000 Ethernet Port.

Table 8

– 10/100/1000 Ethernet MPSoC Pin Assignments

Ethernet PHY Signals

MPSoC Pin

MIO77_GEM3_MDIO

H19

MIO76_GEM3_MDC

H20

MIO74_GEM3_RX_D3

G20

MIO73_GEM3_RX_D2

F20

MIO72_GEM3_RX_D1

E20

MIO71_GEM3_RX_D0

E19

MIO75_GEM3_RX_CTL

F19

MIO70_GEM3_RX_CLK

C20

MIO68_GEM3_TX_D3

G18

MIO67_GEM3_TX_D2

H18

MIO66_GEM3_TX_D1

D19

MIO65_GEM3_TX_D0

A20

MIO69_GEM3_TX_CTL

B20

MIO64_GEM3_TX_CLK

F18

GEM3_RST_N

N/C

The GEM3 peripheral is used on the PS, connected through MIO [64-77] in MIO Bank 502. The Ethernet
Reset signal is active-low and connected to the I/O expander via Port 2,

P2_GEM3_RST_N

. Either of the

push button resets,

PS_POR_B

or

PS_SRST_B

will also generate the active-low Ethernet Reset signal.

The UltraZed-EG SOM also contains an active-low Ethernet PHY interrupt/power down signal that is
connected to the I/O expander via Port 3,

P3_GEM3_PWDN_N

. By default, the end-user can assert this

control signal to enable the Power Down mode of operation for the Gigabit Ethernet PHY. Alternatively, if
the pin is programmed as an interrupt output, interrupts will be asserted low to the I/O Expander. The latter

«
...
12
13
14
15
16
...
»

Summary of Contents for UltraZed-EG
















































Reviews:

No comments

Related manuals for UltraZed-EG

Brand: TA Hydronics Pages: 14

Brand: Eaton Pages: 100

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: halstrup-walcher Pages: 39

Brand: Madas Pages: 6

Brand: Madas Pages: 11

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Total Access 351 Series

Brand: ADTRAN Pages: 4

Brand: Grundfos Pages: 23

Brand: Sungrow Pages: 4

Brand: FrSky Pages: 2

Brand: HEROSE Pages: 92

Brand: bluelab Pages: 39

Brand: SOMFY Pages: 2

Smart 4 Universal

Brand: Classic Pages: 12

Brand: Pilz Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands