Avnet UltraZed-EG Hardware User'S Manual Download Page 11 | Manualshive

Page: 11 / 47

background image

Version 1.0

Page 11

Ult device. For further information on the I/O expander and its connections, please locate the I/O
expander section within this hardware user guide.

eMMC FLASH MEMORY

(8GB)

MTFC8GAKAJCN-4M IT

Bank 500

MIOxx_EMMC0_IO[0:7]

MIO22_EMMC0_CLK

P0_EMMC0_RST_N

MIO21_EMMC0_CMD

I/O

EXPANDER

TCA9534

Figure 5

– eMMC Block Diagram

Table 3

– eMMC Pin Assignment and Definitions

Signal Name

Description

MPSoC Pin

MIO

eMMC Pin

MIO13_EMMC0_IO0

EMMC Data IO [0]

Y12

MIO_13

A3

MIO14_EMMC0_IO1

EMMC Data IO [1]

AC11

MIO_14

A4

MIO15_EMMC0_IO2

EMMC Data IO [2]

W13

MIO_15

A5

MIO16_EMMC0_IO3

EMMC Data IO [3]

V13

MIO_16

B2

MIO17_EMMC0_IO4

EMMC Data IO [4]

AD11

MIO_17

B3

MIO18_EMMC0_IO5

EMMC Data IO [5]

AB12

MIO_18

B4

MIO19_EMMC0_IO6

EMMC Data IO [6]

AE11

MIO_19

B5

MIO20_EMMC0_IO7

EMMC Data IO [7]

AA12

MIO_20

B6

MIO21_EMMC0_CMD

EMMC Command

AD12

MIO_21

M5

MIO22_EMMC0_CLK

EMMC Clock

W14

MIO_22

M6

NOTE: EMMC18 Boot Mode: MODE PINS [3:0]

– 0x6

2.2.4

SFVA625 Device Package Delay Compensation for Memory Interfaces

The Zynq Ult MPSoC device package delay is accommodated for in the layout of the each of the
memory interfaces signal trace lengths. The average of min and max values for package delay is utilized
to compensate for the flight time caused by the delay associated with this package.

2.3 GTR Transceivers

The  UltraZed-EG  SOM  has  four  multi-gigabit  transceiver  lanes  that  reside  on  Bank  505  of  the  Zynq
Ult MPSoC device. These transceivers  can be used to interface to multiple high speed interface
protocols such as PCI Express, Serial ATA, USB3.0, and Display Port. The associated high speed protocol
MAC layers are hardened macros that exist in the PS subsystem of the Zynq Ult MPSoC device
so  additional  Intellectual  Property  (IP)  or  targeted  devices  are  not  necessary  to  complete  the  various
interfaces.

The Zynq Ult MPSoC is enabled with four GTR transceivers which are capable of a transceiver
data rates up to 6.0 Gbps. Four differential MGT reference clock inputs are available to support the GTR
transceiver lanes. The multi-gigabit transceiver lanes and their associated reference clocks are connected
to the end-user carrier board via the JX3 Micro Header.

«
...
9
10
11
12
13
...
»

Summary of Contents for UltraZed-EG
















































Reviews:

No comments

Related manuals for UltraZed-EG

Brand: NEJE Pages: 17

Brand: Oceanic Pages: 13

Brand: Ebyte Pages: 34

Brand: YASKAWA Pages: 61

Brand: Accel Pages: 8

Brand: Manfrotto Pages: 16

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Parker Pages: 44

Brand: Maestra Pages: 22

Brand: Laird Pages: 38

Brand: Laird Pages: 5

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands