Home
/
Avaya
/
G700
/
Installation Manual

Avaya G700, Installation Manual

Share

Page: 207 / 494

Avaya G700 Installation Manual Download Page 207

Configure the G700

Issue 7 January 2005

207

Ping MGP results

2. Check that the same number of packets transmitted were also received.

3. Type

ping voip v0 <IP_address>

<IP_address>

is the address of the G700, or any other functioning endpoint on the

customer’s LAN.

Ping results appear on the screen, similar to the following example.

Ping VoIP results

Setting up the controller list for the G700

Note:

Note:

The Avaya Gateway Installation Wizard (GIW) performs this task automatically.

To complete the configuration of the G700 media gateway, you need to administer a list of
primary and alternate controllers. This list begins with the IP address of the primary controller. In
the event that the G700 media gateway loses contact with its primary controller, it will seek to
re-register with the primary controller first, then with the other controllers on this list. The other
controllers are S8500 or S8700/S8710 media servers that can act as the primary controller, or
S8300 media servers configured as Local Survivable Processors (LSPs).

Up to four IP addresses separated by commas can be entered to form the controller list.

MG-???-1(configure)# ping mgp 135.122.49.55

PING 135.122.49.55: 56 data bytes

64 bytes from 135.122.49.55: icmp_seq=0. time=0. ms

64 bytes from 135.122.49.55: icmp_seq=1. time=0. ms

64 bytes from 135.122.49.55: icmp_seq=2. time=0. ms

64 bytes from 135.122.49.55: icmp_seq=3. time=0. ms

64 bytes from 135.122.49.55: icmp_seq=4. time=0. ms

----135.122.49.55 PING Statistics----

5 packets transmitted, 5 packets received, 0% packet loss

round-trip (ms) min/avg/max = 0/0/0

MG-???-1(configure)# ping voip v0 135.122.49.55

----135.122.49.55 PING Statistics----

5 packets transmitted, 5 packets received, 0 packet loss

round-trip(ms) min/avg/max = 0/1/0

«
...
205
206
207
208
209
...
»

Summary of Contents for G700















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands