background image

1

6

3.6.5 Warning light

An  optional set of warning lights is mounted on the top and 
at  the  base  of  the  lift.  The  flashes  warn  that  the  lift  is 
moving.

3.6.6 Acoustic buzzer

An audible signal is installed with a warning function.

If  the  external  buttons  of  the  user  control  box  or  platform 
control  boxes  are  used,  the  operation  will  be  delayed  and 
an acoustic warning emitted. This way, the persons next to 
or inside the cabin are alerted of an inminent movement of 
the service lift and can act accordingly. This same acoustic 
buzzer sounds while the cabin is overloaded.

Manual descent buzzer sounds during all the descent when 
user performs a manual descent.

3.7 Manual descent system

The  service  lift  has  a  manual  descent  system  that 

can  be  used  in  the  event  of  a  power  failure 
emergency  situation. 

(See  section  4.3.

9

  in  Use  of 

service  lift)

3.8 Guiding system

3.8.1 Guiding ladder

The  service  lift  is  guided  by  ladder.  The  guiding  system 
function  is  to  safely  guide  the  service  lift  along  the  ladder 
stiles.
The guiding system consists of the guiding ladder and 4 sets 
of  2  guiding  rollers  each.  The  arrangement  of  the  4  sets  is 
shown in the following figure.

Each  roller  is  secured  to  the  cabin  supporting  profiles  and 
the surface of the rollers is made of a material that ensures 
smoothness though providing necessary endurance.

Figure 

21

: Guiding system

Guiding system

1

2

Guiding ladder

Top  guiding rollers

Bottom guiding rollers

3

1

2

3

3.9 Cable management

3.9.1 Travelling cable

Travelling  cable  is  connected  from  power  supply  socket 
over mid tower´s height platform to service lift socket and it 
features  a  cable  stocking  on  each  end.  A  travelling  cable 
pulley is suspended on the cable and is guided along the 
traction and safety wire ropes.

3.10 Platform fences

The platform holes shall be protected with platform fences.

 

These  platform  fences  consist  of  structures  of  different

 

geometries  depending  on  the  platforms  where  they  are

 

installed.

 

 

The platform fences shall conform to EN 14122-3 and shall

 

be  equipped  with  a  door  (sliding  and/or  swinging)

 

monitored with a trapped key system. Optionally, and apart

 

from  the  trapped  key  system,  the  platform  fence  doors

 

could  feature  guard  locking  switch  system,  or  an  electrical

 

switch monitoring system.

 

 

3.10.1 Fence door interlock system

3.10.1.1 Trapped-key system

The  platform  fence  door  is  equipped  with

 

a  trapped-key 

lock that keeps the door locked while the service lift is not at 
the platform.  The  door  can  be  unlocked  using  the  trapped 
key  in  the  cabin  and  opening  the  lock.  The  key  will 
remain trapped until the door is closed and locked again.

1

2

3

 

4

 

Travelling cable 

1

2

Travelling cable pulley

Travelling cable

Traction wire rope

Safety wire rope

3

4

Figure 

22

: Travelling cable

Summary of Contents for OCTOPUS XL120





































Reviews: