Avantes AVASPEC-1024 Manual Download Page 89

Page: 89 / 129

Apr-09

Avantes

www.avantes.com

[email protected]

LED Lamp replacement

Plug out the power connector from the
socket.

Remove screw protection caps on the
frontside

Loosen 2 screws with philips
screwdriver

take out the frontplate and electronics
board

untighten 2 screws from LED socket

slightly bend the electrical wires out of
LED socket

take out the LED from LED front holder

replace by new LED, make sure the
Anode and Kathode are connected in the same way and LED legs make no short circuit.

Apply power to see if the LED is illuminating

10.

Slide back electronics board and front plate, tighten screws and put back screw caps

Technical Data

AvaLight-LED380

AvaLight-LED400

AvaLight-LED470

AvaLight-LED590

Power Supply

12 VDC/ 800mA

Spectral
Range*

380 nm

400 nm

470 nm

590 nm

FWHM (nm)

15 nm

11 nm

30 nm

LED output

10 µWatt

25 µWatt

Connector

SMA 905

Power Supply

12 VDC

(+inside, GND outside)

, 40 mA

Dimensions

175 x 110 x 44 mm

* other wavelengths available on request

Ordering Information

AvaLight-LED-XXX

Light Emitting Diode Lightsource, specify wavelength XXX

AvaLight-LED-470-p14

Light Emitting Diode Lightsource, 470 nm for use with AvaSoft-Oxy

AvaLight-LED-XXX-RM

Rackmount version of the Light Emitting Diode Lightsource, specify wavelength

XXX

IC-DB15-2

Interface cable AvaSpec-USB1 platform to AvaLight-LED

IC-DB26-2

Interface cable AvaSpec-USB2 platfom to AvaLight-LED for PWM

PS-12V/1.0A

Power supply 100-240 VAC/12VDC, 1.0 A for AvaLight-LED

Screws LED
Socket

LED front
holder

Summary of Contents for AVASPEC-1024


































































































































Search results

Summary of Contents for AVASPEC-1024

Reviews:

Related manuals for AVASPEC-1024

Brands by name

Popular brands

Avantes AVASPEC-1024, Manual

Search results

Summary of Contents for AVASPEC-1024

Reviews:

Related manuals for AVASPEC-1024

Brands by name

Popular brands