manualshive.com logo in svg

Avantes AVASPEC-1024, Manual

Share
Download
Avantes AVASPEC-1024 Manual Download Page 103

 

102 

 

 

                Apr-09 

 
Avantes 

www.avantes.com 

[email protected]

 

the intensity calibration data will be saved to an ASCII file with extension *.dfr, with bare 
fiber this extension will be *.fbr. The name of the intensity calibration file can be entered 
after clicking the  “Save As” button. 

10.

 

Switch to the Irradiance Chart TAB to enter the hardware setup and select the colorimetric, 
radiometric, photometric and/or peak parameters of interest. Then click OK.  

11.

 

Measure the output parameters in the experiment. If needed, change the integration time, 

such that the maximum in Scope Mode is around 14000 A/D Counts . Block the light path to 
the spectrometer, and save a dark spectrum. If the (ir)radiance of the light to be measured 
needs to be displayed against time, click the time measurement TAB in the settings dialog. 

12.

 

The intensity calibration as performed under point 9 can be loaded in future experiments by 
selecting the option “Load Intensity Calibration”, as described below under Quick Start (2). 
After loading an intensity calibration, a dark spectrum needs to be saved before switching to 
Irradiance mode. 

Technical Data 

 
Wavelength Range 

200-1099 / 1100-2500nm 

Calibration Accuracy 
Repeatability 

± 1 % 

Calibration Relative 
Uncertainty to NIST standard 

± 10 % (200-400nm) 

± 9 % (240-350nm) 

± 10% (350-400nm) 

± 9.5% (400-1100nm) 

Calibration valid for 

60 hrs 

Time to stabilize 

Ca. 30 Min. 

Bulb Output (CC-UV/VIS) 

Ca. 80µW/cm

2

nm (@215nm) 

Ca. 5µW/cm

2

nm (@800nm) 

Power requirement 

100-240VAC 

Dimensions (mm)  

315x165x140 

 

Ordering Information 
AvaLight-DH-CAL 

NIST traceable UV/VIS Deuterium/Halogen Lamp with CC-UV/VIS-CAL 
diffuser, -SR fibers recommended 

AvaLight-DH-CAL-ISP30 

NIST traceable UV/VIS Deuterium/Halogen Lamp for use with AvaSphere-30-
IRRAD, -SR fibers recommended 

AvaLight-DH-CAL-ISP50 

NIST traceable UV/VIS Deuterium/Halogen Lamp for use with AvaSphere-50-
IRRAD, -SR fibers recommended 

AvaLight-DH-CAL-ISP80 

NIST traceable UV/VIS Deuterium/Halogen Lamp for use with AvaSphere-80-
IRRAD, -SR fibers recommended 

DH-Recal 

AvaLight-DH-CAL recalibration service 200-1099nm 

DH-Recal-NIR 

AvaLight-DH-CAL extended or recalibration service 1100-2500nm 

Summary of Contents for AVASPEC-1024


































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands