background image

AV

A

L

O

N

www.avalonbrewer.com

       (800)561-6162

AVALON Gourmet Révision A

AVALON 

Gourmet

Gourmet

Gourmet

Gourmet

Gourmet

INSTALLATION MANUAL

5.7.2

Soluble Canisters

Removing whipping assembly for cleaning
Frequency: Weekly or every 200 cycles

If there is residue, remove the assembly for manual cleaning under hot water:

1.

Remove the tube from the base;

2.

Lift off the funnel and twist off the whipper base;

3.

Rinse thoroughly under hot water and use tube brush if necessary for
tubing area;

4.

Air dry completely;

5.

Reinstall all parts in the reverse order.

6.  Order a large beverage to confirm that all parts or switches have been

 replaced.

Removing canisters for cleaning
Frequency: Monthly or every 1,000 cycles

To ensure a consistent product quality, we recommend removing and
emptying the canisters on a monthly basis. This will ensure that the
product does not adhere to the walls of the canister.

1.

Unlock the door;

2.

Remove the top cap of the machine;

3.

Pull the canister through the top of the brewer to disengage it from the
motor and transmission;

4.

Clean and sanitize under hot water and air dry completely;

5.

Reinstall all parts and reload products in the reverse order.

6. Order a large beverage to confirm that all parts or switches have

been replaced.

Cleaning and Sanitizing

36

5.7.3

Whipper

To remove the assembly of the whipper for cleaning
Frequency: Weekly magazine or every 200 cycles

1. Refer to page 20-21
2. Remove the base of the

 

whipper

3. Rince under hot water
4. Let dry with the free air;
5. Reinstall all the parts in the opposite order;
6. Order a large beverage to confirm that all the parts are in place.

Summary of Contents for Gourmet
















































Reviews: