4
Your Securalift Automatic Garage
Door Opener has many features
which you will appreciate. The
components and materials used in
this Automatic Opener are of the
latest technology and highest qual-
ity. Below are listed some of these
features
OPERATION
To operate the door simply press the
hand held transmitter or the wall
mounted transmitter or optional wall
switch for two seconds and the door
will automatically open or close.
The door can be stopped during an
opening or closing cycle by pressing
again. The next actuation will
move the door in the opposite direc-
tion.
HOPPING CODE
Every time a transmission is made
from the Remote Transmitter a new
security code is generated. The
n u m b e r o f p o s s i b l e c o d e
combinations is over 4.29 billion.
This greatly enhances security of the
system. Code ’Grabbing’ is made a
thing of the past.
ISS (INTELLIGENT SAFETY
OBSTRUCTION SYSTEM)
While the door is doing a closing
cycle and if it should hit an obstacle
or be restricted in some manner, it
will automatically reverse. The
amount of force the door should
encounter before reversing, is
automatically adjusted by the doors
control system, during the initial
installation of the automatic door
opener. The door also if restricted
whilst opening will stop. The Safety
Obstruction Force should be
checked at least once a month. See
installation manual for instructions.
SECURITY CODE STORE
The Opener uses state of the art
technology in storing your selected
Transmitter Security Code.
OPEN AND CLOSE DRIVE
BUTTONS
Another feature developed by
Automatic Technology Australia in
aiding in the installation of the
opener are the Open and Close
Buttons. These buttons are used to
help set the open and close
limit
positions. A quicker setting time
and a more precise limit position
can be achieved using this system.
INITIALISATION
The Reset button on the Door
Opener is used to initialise or re
-initialise the obstruction settings
and door travel counts. See
installation manual for instructions.
AUTO CLOSE MODE
The Opener can be programmed to
automatically close after an open
cycle. The Auto Close time is
adjustable. It is compulsory to in-
stall a Photo Electric Beam if this
mode is selected, otherwise the door
will not operate.
AUTO RUN TIME
If the Motor is left running in the
Opener for any reason the Auto Run
Time will turn the motor off after
thirty seconds.
PHOTO ELECTRIC BEAM
(OPTIONAL)
The Opener has an input for a Photo
Electric Beam to be connected for
extra safety protection.
MANUAL OPERATION
The Opener is equipped with a
unique Manual Disengaging Device.
If the power to the Opener is
disrupted for any reason the door
can be put into Manual Mode by
pulling down on the string handle
on an angle towards the door,
then
releasing. This will allow you to
manually open or close the door. To
re-engage pull the string at an angle
away from the door then release.
Up to 27 different codes can be
stored in the Openers memory.
To store any code simply press and
hold the Door Code button on the
Opener and press the Transmitter
button twice. Each or all codes can be
deleted and changed at any time. The
codes can also be stored from a
remote location.
OVER LOAD INDICATOR
When the maximum opening and
closing capacity of the Opener is
exceeded the Courtesy Light and
Overload LED will flash to indicate
that an Overload has occurred.
SERVICE INDICATOR
The Opener has a Service indicator.
When the Overload LED lights up
continuously it means that the opener
and, or garage door needs a service.
AUTO COURTESY LIGHT
The Courtesy Light on the Opener
comes on automatically whenever the
door is activated to do an opening or
closing cycle. The Light can also be
switched on and off without
operating the door. This is done by
pressing the button on the Hand Held
Transmitter or Wall Mounted Trans-
mitter which has being stored as the
light code, or by pressing the light
button on the Wall Switch (optional).
The light will stay on for
approximately three minutes then go
off.. This time is also adjustable.
CAS (COLOUR ASSISTED
SETTINGS)
To make the installation of the
Automatic Opener more user friendly
Automatic Technology Australia
developed the CAS (Colour Assisted
Settings) system. This unique system
allows for all the Open and Close
adjustments and settings to be colour
coordinated, Red for Close and Green
for Open. The colour coordination
make its easier and quicker for the
user or installer to complete the
installation.
F E AT U R E S
Summary of Contents for SECURALIFT
Page 16: ...PARTS LIST...
