AutoAnchor 560 Owner'S Manual Download Page 7

Page: 7 / 41

Dual Installation

Use the T junction connector Part #9506 and the 2m (Male/Female) extension cable Part

#9505.

2.1.4 REED SWITCH SENSORS

Some windlasses are supplied pre-ﬁtted with a reed switch sensor. Reed switch sensors

must have a 10mm x 8mm magnet (#9061) and the gap between the reed switch sensor

and the magnet must be a minimum of 3mm and a maximum of 5mm. This sensor requires

a ﬁeld connector.

The AutoAnchor will operate with a reed switch sensor for all-chain rode. If using rope/

chain rode the reed switch sensor provides a reasonably accurate count of rode deployed

but on retrieval the display may be incorrect because it cannot allow for the stretch in the

rope.

For an accurate rope and chain count, the reed switch sensor should be replaced with the

AA grey sensor (#9067).

2.1.5 PLUG AND PLAY SENSOR TUNING

When the AutoAnchor is completely installed the sensor must be tuned. See the

instructions on page 21.

Part

#9506

AutoAnchor

AA560

Console

Down

AutoAnchor

AA560

Console

Down

Chainwheel

Sensor

Part #9505

Summary of Contents for 560










































Search results

Summary of Contents for 560

Reviews:

Related manuals for 560

Brands by name

Popular brands

AutoAnchor 560, Owner'S Manual

Search results

Summary of Contents for 560

Reviews:

Related manuals for 560

Brands by name

Popular brands