manualshive.com logo in svg

AUTHOR Alarm IGLA, Service Manual

Share
Download
AUTHOR Alarm IGLA Service Manual Download Page 41

38

If  connection  has  not  been  successful,  flashing  of 

the diode will stop in 30 seconds after installation 

of the power supplying element and the key fob will 

be transferred in the «sleep» mode with low energy 

consumption. In this case, repeat the pairing procedure 

once again. The key fob leaves the «sleep» mode after 

having been moved.

Check out the key fob workability after pairing it with 

the device. Ensure it is displayed in the Author Config 

application (available for Android only).

Authentication by the key fobs of the KEYLESS BLOCK

The authentication process in the IGLA ALARM can be 

undergone by the key fobs included in the KEYLESS 

BLOCK set. For this purpose, the devices should be 

aligned (see page 24).

Disarming of the IGLA ALARM happens right after 

disarming of the KEYLESS BLOCK by exchanging with 

the encrypted messages with each other through 

the regular CAN-bus of the car. If the two-step 

authentication mode is turned-on, the PIN-code is 

necessary to be entered with the standard buttons.

Summary of Contents for IGLA

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands