AudioCodes Mediant 1000 MSBG Cli Reference Manual Download Page 4

Page: 4 / 160

CLI Reference Guide

Document #: LTRT-17940

System and VoIP Functionalities

4.9

snmp trap............................................................................................................. 52

4.10

snmp trap destination........................................................................................... 53

4.11

snmp v3-users ..................................................................................................... 54

4.12

tls ......................................................................................................................... 55

VoIP Commands ............................................................................................... 57

5.1

interface ............................................................................................................... 57

5.1.1

E1/T1, bri ................................................................................................................. 57

5.1.2

fxs-fxo ...................................................................................................................... 59

5.1.4

enm ......................................................................................................................... 61

5.1.5

debug capture voip.................................................................................................. 63

5.2

Network Interface Configuration ........................................................................... 65

5.2.1

interface network-if .................................................................................................. 65

5.2.2

interface vlan ........................................................................................................... 67

5.2.3

application_type ...................................................................................................... 68

5.2.4

ip address ................................................................................................................ 69

5.2.5

ip gateway ............................................................................................................... 70

5.2.6

ip name-server ........................................................................................................ 71

5.2.7

desc ......................................................................................................................... 72

5.2.8

show mode .............................................................................................................. 73

5.3

routing static ........................................................................................................ 74

5.4

qos vlan-mapping ................................................................................................ 75

5.5

qos application mapping ...................................................................................... 76

5.6

coders-and-profiles coders-group ........................................................................ 77

5.7

coders-and-profiles ip-profile................................................................................ 78

5.8

coders-and-profiles tel-profile ............................................................................... 80

5.9

control-network .................................................................................................... 82

5.9.1

NATTranslation ....................................................................................................... 82

5.9.2

dns Dns2Ip .............................................................................................................. 83

5.9.3

dns Srv2Ip ............................................................................................................... 84

5.9.4

ip-group ................................................................................................................... 85

5.9.5

proxy-ip ................................................................................................................... 86

5.9.6

proxy-set ................................................................................................................. 87

5.9.7

sip-interface ............................................................................................................. 88

5.9.8

srd ........................................................................................................................... 89

5.10

ip-media ip-media-settings ................................................................................... 90

5.11

ldap ...................................................................................................................... 91

5.12

SAS ..................................................................................................................... 92

5.12.1

stand-alone-survivability ......................................................................................... 92

5.13

sip-definition ........................................................................................................ 94

5.13.1

account .................................................................................................................... 94

5.13.2

account setting ........................................................................................................ 95

5.13.3

advanced settings ................................................................................................... 96

5.13.4

general settings ....................................................................................................... 98

5.13.5

proxy and registration............................................................................................ 100

5.14

sbc ..................................................................................................................... 102

5.14.1

allowed-coders-group............................................................................................ 102

5.14.2

general-setting ...................................................................................................... 103

5.14.3

manipulations ip-inbound-manipulation ................................................................ 104

5.14.4

manipulations ip-outbound-manipulation .............................................................. 105

5.15

routing ............................................................................................................... 106

5.15.1

classification .......................................................................................................... 106

5.15.2

condition-table ....................................................................................................... 107

Summary of Contents for Mediant 1000 MSBG

































































































































































Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands

AudioCodes Mediant 1000 MSBG, Cli Reference Manual

Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands