AudioCodes Mediant 1000 MSBG Cli Reference Manual Download Page 70

Page: 70 / 160

CLI Reference Guide

Document #: LTRT-17940

System and VoIP Functionalities

5.2.5

ip ga

eway

This command defines the gateway IP address on the specified Layer 3 interface.

Syntax:

ip gateway

The command’s syntax format is described below:

Arguments

Description

Specifies a valid IPv4 address. IP addresses should be
expressed in dotted decimal notation (for example, 10.1.2.3).

Defaults

Command Modes

Enable

Examples:

The following example configures the gateway IP address 10.4.0.1 for interface VLAN 3.

(config-voip)# interface vlan

(conf-if-vlan 3)# ip gateway

10.4.0.1

Summary of Contents for Mediant 1000 MSBG

































































































































































Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands

AudioCodes Mediant 1000 MSBG, Cli Reference Manual

Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands