AudioCodes Mediant 1000 MSBG Cli Reference Manual Download Page 122

Page: 122 / 160

CLI Reference Guide

122

Document #: LTRT-17940

System and VoIP Functionalities

5.16.7 hunt

trunk-group-setting

This command defines the trunk group settings.

Syntax:

gw hunt trunk-group-setting

<index>

set

The command’s syntax format is described below:

Arguments

Description

<index>

Defines the table row index.

Sets the following table parameters:



ChannelSelectMode



ContactUser



GatewayName



MWIInterrogationType



RegistrationMode



ServingIPGroup



TrunkGroupId



defaults

For a description of these parameters, refer to the

User's Manual

Defaults

Command Modes

Enable

Examples:

The following example enables the Profile iD.

(config-voip)#

gw hunt trunk-group-setting

(trunk-group-setting-18)

# set gatewayname

gateway1

Summary of Contents for Mediant 1000 MSBG

































































































































































Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands

AudioCodes Mediant 1000 MSBG, Cli Reference Manual

Search results

Summary of Contents for Mediant 1000 MSBG

Reviews:

Related manuals for Mediant 1000 MSBG

Brands by name

Popular brands