Atronic e-motion Page 25 Operating Manual Download

Page: 25 / 59

April 2007

e-motion™ Operating Manual - B-Level STD

ACHINE

ANDLING

CELEBRATION LIMIT

If enabled, the celebration limit determines a threshold

for jackpot handpays. A win that exceeds the adjusted

limit initiates a jackpot celebration and needs to be

acknowledged by an attendant using the jackpot key.

Open the Service Menu and select "Settings / Lock

Options / Limits" to enable/disable and adjust the

celebration limit (default setting = celebration limit

disabled).

Celebration Limit

On / Off

Enables or disables the celebration limit.

Lower

Sets the threshold for the lower celebration limit

(in credits). A win that exceeds this limit, initiates

a handpay or can be booked to card or credit meter,

depending on setting CELEBRATION LIMIT

DESTINATION.

Upper

Sets the threshold for the upper celebration limit

(in credits). A win that exceeds this limit always

initiates a handpay.

Celebration Limit Destination

Sets the destination for wins exceeding the lower

but not the upper celebration limit.

• With cashless transaction mode EFT the settings

HANDPAY and CARD are selectable.

Note

: If celebration limit destination has

been set to CARD, and no player card is

available/operational, the amount is booked

to the credit meter instead.

Jackpot handpay initiated by a win that
exceeds the adjusted celebration limit.

Summary of Contents for e-motion




























































Search results

Summary of Contents for e-motion

Reviews:

Related manuals for e-motion

Brands by name

Popular brands

Atronic e-motion, Operating Manual

Search results

Summary of Contents for e-motion

Reviews:

Related manuals for e-motion

Brands by name

Popular brands