Atronic e-motion Page 14 Operating Manual Download

Page: 14 / 59

April 2007

e-motion™ Operating Manual - B-Level STD

PLAY

LINE

PLAY

LINES

PLAY

LINES

PLAY

LINES

PLAY

LINES

CREDIT

PER LINE

BET 1

CREDITS

PER LINE

BET 2

CREDITS

PER LINE

BET 3

CREDITS

PER LINE

BET 5

CREDITS

PER LINE

BET 10

CREDITS

MAX BET

210

G
A

B
L
E

REPEAT

THE
BET

REPEAT

THE
BET

SEE

PAYS

BUTTON PANEL / SELECT BET

Depending on remaining credits, possible bets are

indicated by lit and flashing buttons.

1.Select the number of lines to play.

Selectable PLAY X LINES buttons are lit.

2. Select the bet per line. Selectable BET X CREDITS

PER LINE buttons are flashing.

The game starts immediately with the selected

bet.

TOTAL BET = LINES x BET PER LINE

If a certain combination of LINES and BET PER LINE

is not lit, there are not enough credits to play this

bet. Insert money or play another bet.

Note:

Figures are for example only. Other bet/line

configurations may use different bet/line steps.

AMEPLAY

PLAY

LINE

PLAY

LINES

PLAY

LINES

PLAY

LINES

PLAY

LINES

CREDIT

PER LINE

BET 1

CREDITS

PER LINE

BET 2

CREDITS

PER LINE

BET 3

CREDITS

PER LINE

BET 5

CREDITS

PER LINE

BET 10

CREDITS

MAX BET

210

G
A

B
L
E

REPEAT

THE
BET

REPEAT

THE
BET

SEE

PAYS

Summary of Contents for e-motion




























































Search results

Summary of Contents for e-motion

Reviews:

Related manuals for e-motion

Brands by name

Popular brands

Atronic e-motion, Operating Manual

Search results

Summary of Contents for e-motion

Reviews:

Related manuals for e-motion

Brands by name

Popular brands