background image

22

April 2007

e-motion™ Operating Manual - B-Level STD

HANDPAY 

(continued)

Jackpot Handpay during Cash Fever™ Bonus Games

If the highest progressive jackpot level was hit dur-

ing a bonus game session, the machine will lock up

and displays a jackpot message on-screen:

<amount> JACKPOT WILL BE PAID AT THE END OF THE BONUS GAME

At the same time a handpay message of the progres-

sive jackpot amount is send to the accounting system.

However, no handpay must be carried out at this

time! 

The on-screen message instructs the attend-

ant to pay the player 

after

 all remaining bonus spins

are played. The remaining bonus game spins are played

after the jackpot message has been reset by turning

the jackpot key.

When all bonus game spins are played, the game

shows a result screen. It shows the credits won dur-

ing the bonus game, the progressive jackpot win and

the totalized win amount (in credits).

After a few seconds the game will lock up again show-

ing a handpay screen and following message

CALL ATTENDANT FOR HANDPAY <amount>

At the same time a second handpay message (level

00) of the additional wins achieved during the bonus

game session is send to the accounting system. The

handpay message needs to be reset with the jackpot

key and the 

total win amount

 that is displayed in

the lower game screen has to be paid via handpay.

Note

:  Depending on the casinos handpay handling

rules, a pay out of the totalized win amount in one

piece may require a manual override of the two (par-

tial) handpay messages at the accounting system.

To prevent an attendant from paying a jackpot twice,

carefully check the on-screen messages whether

you have a real handpay situation or an indication

of a handpay to come up soon.

M

ACHINE

 H

ANDLING

Summary of Contents for e-motion




























































Reviews: