background image

 
 
 
 
 

 

VERIFICATIONS AND TESTING TO BE DONE 

BEFORE THE INSTALLATION 

To ensure that the installation and the use of this product are safe, 

you must

 follow the instructions in this manual. 

Please pay special attention to the following points.

 

 

AUTOMATIC TRANSMISSION VEHICLE 

 

Ensure that the vehicle 

cannot

 be remote started when in gear. Also ensure that the gearshift 

lever 

cannot

 be moved out of the "Park" position without first applying the brakes. 

If it is possible to crank the engine while the gearshift lever is in gear, or if you can 
move the gearshift lever out of "Park" position without pressing on the brakes, 
contact our Technical Assistance Department at 

1-800-461-8223

. A technical 

advisor will help you with an appropriate and safe solution based on the make and 

model of the vehicle on which you are working. 

 

Once the installation is completed, you must check ALL safety devices described in the "POST-
INSTALLATION AND SECURITY TESTS" on page 26 of this guide. 

MANUAL TRANSMISSION VEHICLE

 

 

 Make sure you have in hand a “manual interface module” part no. RS-MI (not included) 

specially made to safely install the remote starter in a manual transmission vehicle. 

 

 Make sure that 

all

 door pin switches work and that the parking brake is operational (i.e. it can 

immobilize the vehicle). These security features must be operational before the installation of the 
remote starter. 

 

 Make sure it is 

impossible

 to access the gearshift lever without opening a door or the 

hatchback. 

 If the gearshift lever can be accessed without opening a door (i.e. convertibles) or if 

opening any one door does not break the safety sequence, we

 strongly 

recommend adding a motion detector (microwave) to prevent a start if any activity 
is detected near the gearshift lever. See details on the manual interface 

instructions. 

 

 Once the installation is completed, you must check ALL safety devices described in the 

"POST-INSTALLATION AND SECURITY TESTS" on page 26 of this guide. Make sure the 
opening of each door and/or of the hatchback (one at a time) breaks the safety sequence that 
normally allows the system to initiate a remote start sequence. 

Summary of Contents for BBF































Reviews: