manualshive.com logo in svg

Assum DZ SERIES, Operation Manual, Page: 19 / 33

Share
Download
Assum DZ SERIES Operation Manual Download Page 19

17

to adjust the vacuum time in the range of (0-99) seconds.

G

Running indicator Indicator lights (red) when machine during the operating

H

Sealing time adj.

Press enter into sealing time adjust, up and down buttons
to adjust the sealing time in the range of (0-6) seconds.

I

Temperature light

When machine work, indicator light (red) when machine
do sealing function.
When using the temperature selector button to select a
certain temperature, the corresponding temperature
indicator light (red)

J

Temp. meter

shows the vacuum chamber pressure.

Be careful! scald!

Machine hot plate sealing surface temperature up to 200

℃

.

Even after cooling, the surface still has a high temperature.

Harmful to health!

Vacuum reside exhaust gas there.
Long-term inhalation of gases harmful to health.

Use of this product room must have good ventilation.

6.Standard operation &parameter setting

Be careful! Injured!

Please refer to this manual to operate the machine.

Shall not remove necessary protection covers or housing.

Do not use this machine to pack goods which will be damaged during vacuum or
after vacuum.

If you operate the machine and function in doubt, when instructions not to
provide relevant information, please contact the manufacturer or supplier.

If the machine is not operating properly, or makes strange noises, immediately
turn off the power, stop the machine and run it off.

event of failure, please contact the manufacturer or supplier.

Summary of Contents for DZ SERIES


































Reviews:

No comments