Associated Equipment 12-2415 Manual Download Page 32

Page: 32 / 37

(BESA-12V24G) User Manual

Version GS 17628

While in display Fig.90, select which results you need to view by scrolling





key and then

press key will get into the test result display as example shown (Fig.91).

2. Press USB key on the keypad will display (Fig.92) as shown below:

It will remain in this display while logging into the PC. Do not press any other keys because the
Analyser is already communicating with the PC.

Step 5.

On the PC, go to desktop display and look for icon. Left click on the icon to open the program
and the display page will show as below:

Click Header &
Footer here to
put your
Company name
and address.

It will automatically
detect COM Port.

COM Port

Customer name

Battery Brand

or Model

Add the above particulars

to test report.

Save

Fig.90

Fig.92



367061WS2337E

SZC3466MZ

MR. KINGSLEY

CAL2115EM

12.65 V

[560 CCA]

480 CCA

8.65 m

Ω

79 %

Fig.91

Transfer data from

Analyser

Summary of Contents for 12-2415






































Search results

Summary of Contents for 12-2415

Reviews:

Related manuals for 12-2415

Brands by name

Popular brands

Associated Equipment 12-2415, Manual

Search results

Summary of Contents for 12-2415

Reviews:

Related manuals for 12-2415

Brands by name

Popular brands