S t e p 1 T E A M / F T
12
s t e p 1
ASSEMBLE REAR A-ARMS
Twist the #7354 rear suspension arms from the mold
runners with pliers and trim away any remaining molding
with your hobby knife.
1
MOUNT REAR A-ARMS & REAR BUMPER
Attachrear bumper to the chassis with two
#6922 screws. Tighten only until they are flush
with the top of the bumper.
7354
left arm shown
7651
left mount shown
7356
6299
7657
6925, 7873*
6299
B A G I
REMOVE THESE
PARTS FOR:
Steps 1-2
T O O L S U S E D
.050"
1:1
7368, qty 4
thin shim
7381, qty 2
set screw
6588, qty 1
black grease
7380, qty 2
MIP CVD axle
7379, qty 2
MIP CVD bone
7381, qty 2
coupling
3977, qty 4
3/16 x 3/8 ball bearing
unflanged
1:1
7381, qty 2
cross pin
1:1
7377, qty 2
spacer
7367, qty 2
hub carrier
7369, qty 2
spring pin
7368, qty 2
thick shim
6299, qty 4
E-clip
7383, qty 1
MIP thread lock
5
6925, 7873*
6922
7529
7260
7652
left mount shown
R T R
T E A M / F T
6922
7775
7775
s t e p 2
1:1
1:1
1:1
1:1
1:1
s t e p 1 T E A M / F T
TEAM/FT ONLY: ASSEMBLE MIP CVD'S
Spread some #6588 Associated black grease inside the #7380 axle hole where
shown, then on the #7381 coupling. Slide the coupling into the axle.
Slide the axle into the #7379 dogbone, aligning the cross holes.
Insert the #7381 cross pin, spacing it evenly on both sides of the bone.
Add the #7383 MIP thread lock to the #7381 set screw. Angle and turn the CVD
so the set screw can be screwed in with the Allen wrench.
Repeat steps 1-4 for the remaining CVD.
Slide one #7368 thick shim onto the #7380 axle. Slide one #3977 unflanged
bearing onto the axle. Push the CVD assembly into the back of the #7367 rear
hub carrier.
Slide one #7377 spacer into the hub carrier from the
front followed by the second #3977 bearing.
Slide two #7368 thin shims onto the axle.
Install the #7369 drive pin with your
needlenose pliers.
Assemble the other hub carrier.
5
7369
7368
3977
7377
7367
7368
7380
7381
7379
7381
coupling
7381
6588
7383
thread lock
3977
9
6299
F R O
N T
Attach the #7354 left rear a-arm to the #7651 (RTR) or #7652
(TEAM/FT) left rear arm mount with one #7356 hinge pin.
Add #6299 E-clips to both ends of the hinge pin.
Attach the #7657 a-arm shock mount to the rear a-arm with two
#6925 (7873*) screws.
Do the right a-arm.
Attach the left rear arm assembly to the chassis with two
#7775 screws.
Attach the right rear arm assembly to the chassis with two
7775 screws.
Finish tightening the bumper screws.
Add two #7260 nuts to the top of the screws.
T E A M B U I L T
TEAM BUILT
7378, qty 2
stub axle
S t e p B T E A M B U I L T
TEAM BUILT
5407, qty 4
red O-ring
1:1
6466, qty 2
1/8" spacer
1:1
6381, qty 2
rear outer hinge pin
1:1
7365, qty 2
hub carrier
6299, qty 4
E-clip
1:1
6375, qty 2
roll pin
1:1
6388, qty 2
cone washer
1:1
7360, qty 4
1/4 x 3/8 bushing
unflanged
1:1
6372, qty 2
dogbone spacer
1:1
6372, qty 2
dogbone spring
6374, qty 2
stub axle
7361, qty 2
dogbone
S t e p 2 T E A M / F T
S t e p A R T R
S t e p A R T R
