background image

7-7

SORGENTE/SMILE/ISI-T/UNDERCOUNTER - Installation, Use and Maintenance - cod. A-MAN03 - Rev. 02/2012

7.3.3 

Set Check

To check the correct set value it will be necessary to press 
the rear programming key and count the number of beeps.

7.3.4 

Signallings and acoustic alarms

Filter exhaustion pre-alarm:

2 beeps every 15 seconds. The beeps repeat every time
a dispensing key is pressed.

Refrigerator alarm: 

  If for technical reasons or for possible clogging in the 

heating exchanger, 

the cooling system should not reach 

the pre-set temperature in 6 hours

, the cooling system 

must be switched off and the water dispensing interrupted. 
In this case, will appear a fixed red Led 2 positioned above 
the right key, (cold water dispensing) followed by 7 beep 
every 15 seconds; moreover, every time the dispensing 
keys are pressed the 7 beep are repeated. 

Filter exhaustion pre-alarm: 

  This function follows the filter pre-alarm A1. 

The machine 

is blocked when the filter is completely exhausted

  In this case, the red Led 1 above the left dispensing key 

(room temperature water dispensing) starts to blink and 
it is followed by a 15 seconds long beep which will be 
repeated each time the dispensing keys are pressed. 

The 

machine could be restarted only by replacing the filter 

and inserting the smart card, supplied with the new 

filter, in the proper fissure, see paragraph 8.3.

Pump blockage.

 

  In case the pump is not able to restore the water level 

in the carbonator in 3 minutes, 

the pump is blocked to 

avoid  any  damages

.  In  this  phase  will  appear  a  fixed  

red Led 2 on the right, positioned above the right key 
(cold still water dispensing), followed by 6 beep every 
15 seconds.

smart card wrong insertion error. 

   The machine will not accept the smart card put in a wrong 

way. By inserting the smart card, in the right way, a 5 
long beep will be heard and OK will appear on the display. 
Then take out the smart card.

ATTENTION: The remote control keypad is operating cor-
rectly when the red operation led lights on when any key 
is pressed.

Summary of Contents for ISI-T





































































Reviews: