background image

Copyright © 2018, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights 
reserved. Reproduction in whole or in part without the express written permission of ASSA 
ABLOY Accessories and Door Controls Group, Inc. is prohibited.

700002-Rev N   09/18

®

5800 ADAEZ   PRO
Installation and Operation Instructions

1 of 50

®

5800 ADAEZ  PRO

Installation and

Operating Instructions

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications.

Note

Changes or modifications not expressly approved by the party responsible for compliance could void the 
user's authority to operate this device. This device complies with part 15 of the FCC Rules. Operation is 
subject to the condition that this device does not cause harmful interference.

To obtain the latest manual and template revisions or to view installation and programming videos go to 
www.nortondoorcontrols.com.  For technical support call 800-438-1951 x6030, option 4.

IMPORTANT INSTALLATION INSTRUCTIONS

READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS

WARNING – To reduce the risk of severe injury or death:

TESTED TO COMPLY WITH

FCC STANDARDS

      

WARNING:

 This product can expose you to chemicals including 

lead, which is known to the State of California to cause cancer or other 

reproductive harm.  For more information go to 

www.P65warnings.ca.gov/product.

Summary of Contents for 5800 ADAEZ PRO



















































Reviews: