ASEM CPU 1021/A User Manual Download Page 58 | Manualshive

Page: 58 / 69

background image

CPU 1021/A

User’s Guide

50

Asem S.p.A.

No Execute Mode Mem Protection

[Enabled]: the function is enabled
[Disabled]: the function is disabled

Intel ® Virtualization Technology

[Enabled]: the function is enabled
[Disabled]: the function is disabled

MCH Control Sub-menu

GMCH Power Management Mode [Default: Legacy]

Allows “Enhanced Power Management” of the Northbridge (register
PMCFG - MCHBAR offset F10h, bit 4). This mainly concerns the power-
down of the memory in power saving states C3 and C4, and transition to
states C3 and C4 if the busmaster is active. If the C-States are not used,
leave the default setting: Legacy

C2 to C3 Transition Timer [Default: 6h]

Reserved

C3 to C4 Transition Timer [Default: 8h]

Reserved

«
...
56
57
58
59
60
...
»

Summary of Contents for CPU 1021/A






































































Reviews:

No comments

Related manuals for CPU 1021/A

Brand: Panasonic Pages: 35

Brand: Intel Pages: 48

Brand: fadini Pages: 32

Brand: Rabbit Pages: 144

Side-Power SEP IP Series

Brand: SLEIPNER MOTOR AS Pages: 28

Brand: Xeltek Pages: 19

Brand: Biostar Pages: 49

Brand: MATSONIC Pages: 76

Brand: P&E Microcomputer Systems Pages: 53

Brand: Quick Pages: 32

Brand: JETWAY Pages: 38

B85-IE35 Series

Brand: MSI Pages: 190

Brand: Zamel Pages: 2

Brand: Tadao Pages: 3

Brand: Intel Pages: 74

Brand: Global American Pages: 37

Brand: Gigabyte Pages: 93

Brand: IBASE Technology Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands