ASEM CPU 1021/A User Manual Download Page 5

Page: 5 / 69

Summary

Chapter 1 Description ......................................................................... 1

Technical specifications .................................................................. 2

Chip-set Intel

ICH8M ................................................... 3

DRAM system memory ................................................................... 3

Video sub-system ............................................................................ 4

LCD display connection ............................................................... 5

Floppy disk controller ...................................................................... 5

IDE controller .................................................................................. 5

SATA controller ............................................................................... 5

Parallel port ..................................................................................... 6

Serial ports ...................................................................................... 6

LAN1 10/100/1000 Mbps Port ......................................................... 6

LAN2 10/100/1000(opt.) Mbps Port ................................................ 7

USB (Universal Serial Bus) ports .................................................... 7

Firmware Hub .................................................................................. 7

Real time clock and CMOS memory ............................................... 8

Compact Flash ................................................................................ 8

Hardware monitor ............................................................................ 8

Watch-dog ....................................................................................... 9

Selection of generated signal (JP15) .......................................... 9

States of watch-dog ..................................................................... 9

Summary of commands ............................................................ 10

Summary of readable state bits ................................................. 11

Management Software .............................................................. 11

Chapter 2 Hardware setup .............................................................. 13

Layout CPU 1021/A with highlighting of jumpers .......................... 14

Selection of power supply voltage of LCD panel (JP1) ............. 16

Reset CMOS (JP4) .................................................................... 16

Selection BUS PCIe X1

– X4 (JP5) ........................................... 16

Bios recovery (JP6) ................................................................... 17

Display LCD resolution (JP7, JP8, JP9) .................................... 17

Enable controller LAN1 (JP10) .................................................. 17

Enable warning CPU temperature (JP11) ................................. 17

Reset Watch Dog (JP15) ........................................................... 18

Selection of type of dimming control and Backlight (JP2, JP3,
JP16, JP17, JP18) ................................................................. 18

Selection of power supply (JP21 - JP22) ............................... 18

Chapter 3 Connectors ....................................................................... 19

Layout CPU 1021/A with highlighting of connectors ..................... 20

External connectors ...................................................................... 25

Summary of Contents for CPU 1021/A






































































Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands

ASEM CPU 1021/A, User Manual

Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands