ASEM CPU 1021/A User Manual Download Page 59

Page: 59 / 69

BIOS Setup

Asem S.p.A.

Video (Intel IGD) Control Sub-Menu

Default Primary Video Adapter

Select the primary VGA device (if there is also a PCI device besides the
onboard one).
IGD (default)

the start-up device will be the integrated graphic device.

PEG: the start-up device with be the PCI card.

IGD - Device 2

Disabled: disables the integrated graphic device.
Auto (default): enables the integrated graphic device.

IGD - Device 2, Function 1

Disabled: disables the second graphic device.
Auto (default): enables the second graphic device.

IGD - Boot Type

Lets you select the type of display that will be used during the bootstrap.
CRT + LFP SDVO (default): allows use of both displays, CRT and LCD.
Other settings: the selected displays will be enabled during the
bootstrap.

IGD - S3 Popup

Reserved
Default Disabled.

Summary of Contents for CPU 1021/A






































































Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands

ASEM CPU 1021/A, User Manual

Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands