ASEM CPU 1021/A User Manual Download Page 52

Page: 52 / 69

CPU 1021/A

User’s Guide

Asem S.p.A.

IDE Primary/Master

IDE Channel 0 Master [recommended AUTO]

Multi-Sector Transfers

•

Determines the number of sectors that the disk can access at the
same time

LBA Mode Control

•

LBA (Logical Block Addressing) must be activated for disks with a
capacity of more than 528MB.

32 Bit I/O

•

This setting enables or disables 32 bit IDE data transfer .

Transfer Mode

•

Determines method of data transfer from or to drive.

Ultra DMA Mode

•

Determines the Ultra DMA data transfer mode.

IDE Channel 0 Slave

Multi-Sector Transfers

•

Sets the number of sectors that the disk can access at the same
time

LBA Mode Control

•

LBA (Logical Block Addressing) must be activated for disks with a
capacity of more than 528MB.

32 Bit I/O

•

This setting enables or disables 32 bit IDE data transfer .

Summary of Contents for CPU 1021/A






































































Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands

ASEM CPU 1021/A, User Manual

Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands