ASEM CPU 1021/A User Manual Download Page 53

Page: 53 / 69

BIOS Setup

Asem S.p.A.

Transfer Mode

•

Determines method of data transfer from or to drive.

Ultra DMA Mode

•

Determines the Ultra DMA data transfer mode.

SMART Monitoring

•

This function monitors the hard disk and identifies any problems
with them.

SATA Port 1

Multi-Sector Transfers

•

Sets the number of sectors that the disk can access at the same
time

LBA Mode Control

•

LBA (Logical Block Addressing) must be activated for disks with a
capacity of more than 528MB.

32 Bit I/O

•

This setting enables or disables 32 bit IDE data transfer .

Transfer Mode

•

Determines method of data transfer from or to drive.

Ultra DMA Mode

•

Determines the Ultra DMA data transfer mode.

SMART Monitoring

•

This function monitors the hard disk and identifies any problems
with them.

Summary of Contents for CPU 1021/A






































































Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands

ASEM CPU 1021/A, User Manual

Search results

Summary of Contents for CPU 1021/A

Reviews:

Related manuals for CPU 1021/A

Brands by name

Popular brands