Arcus DMX-CAN-23 Manual Download Page 42

Page: 42 / 74

DMX-CAN Manual

page 42

rev 1.6

Device name

DOBOOT

DO configuration at boot-up

EDO

Enable in-pos/alarm outputs

EOBOOT

EO configuration at boot-up

LCA

Limit correction amount

POL

Polarity settings

ASCII response type

SL, SLR, SLE, SLT,

SLA, SLM

StepNLoop parameters

Table 7.10

Default Settings

Following are the factory default settings when then unit is shipped from the factory.

Command

Parameter Description

Value

Baud-rate (for CANOpen)

125000 bps

Communication Method

RS-232

CURI

Idle Current

1000 mA

CURR

Run Current

1600 mA

CURT

Idle Time

500 mSec

Baud Rate (for RS-232/RS-485)

9600 bps

Device ID

DMC01

DOBOOT

Digital Output Boot-up State

EDO

Alarm/ In Pos Output Mode

Enabled

EOBOOT

Enable Output Boot-up State

LCA

Limit Correction Amount

1000

NID

Node ID (for CANOpen)

POL (bit 1)

Direction Polarity

POL (bit 4)

Limit Polarity

Active Low

POL (bit 5)

Home Polarity

Active Low

POL (bit 6)

Latch Polarity

Active Low

POL (bit 7)

In Position Output Polarity

Active Low

POL (bit 8)

Alarm Output Polarity

Active Low

Response type

Do Not Append

StepNLoop

Enabled

SLA

StepNLoop Maximum Attempt

SLE

StepNLoop Error Range

1000

SLM

StepNLoop Idle Tolerance

SLT

StepNLoop Tolerance Range

Summary of Contents for DMX-CAN-23











































































Search results

Summary of Contents for DMX-CAN-23

Reviews:

Brands by name

Popular brands

Arcus DMX-CAN-23, Manual

Search results

Summary of Contents for DMX-CAN-23

Reviews:

Brands by name

Popular brands