8-9
8
3. Remove the ski. Account for the rubber damper and
washers.
INSPECTING
1. Inspect the ski for cracks or deterioration.
2. Inspect the ski for abnormal bends or cracks.
3. Inspect the wear bar for wear.
4. Inspect all hardware and the spindle bushings for
wear and damage.
5. Inspect the rubber damper for damage or wear.
INSTALLING
1. On F/M/XF models, slide a washer onto the cap
screw used to secure the ski; then apply all-tempera-
ture grease to the shaft portion of the cap screw and
spindle axle.
0745-987
2. Install the spindle axle into the spindle; then position
the ski damper into the bottom of the ski making sure
the damper is properly positioned for the desired ski
stance.
NOTE: The ski damper must be positioned in the ski
so it is directly under the spindle.
3. With the cap screw hole of the ski centered with the
spindle axle, slide the cap screw with washer through
the outside of the ski and spindle assemblies.
NOTE: Local laws and/or regulations as to maxi-
mum width of the ski stance may be applicable.
Always comply with the maximum width laws and/or
regulations when adjusting ski stance.
NOTE: Install the cap screw so the lock nut will be
located to the inside of the ski and the cotter pin slot
in the cap screw will be horizontal with the ski.
4. Install the remaining washer and lock nut; then
tighten the lock nut to 35 ft-lb.
NOTE: Assure that the cotter pin slot in the cap
screw is still horizontal with the ski (see illustration);
then proceed to step 5.
5. Install the cotter pin from the back side of the ski cap
screw and spread the pin.
Ski Wear Bar
The ski wear bar is a replaceable bar attached to the
underside of the ski. If the snowmobile is operated pri-
marily in deep snow, ski wear bar wear will be minimal;
however, if the snowmobile is operated on terrain where
the snow cover is minimal, the ski wear bar will wear
faster. Arctic Cat recommends that the ski wear bars be
replaced if worn to 1/2 of original diameter.
REMOVING
1. Remove ice and snow buildup from the ski.
2. Raise the front of the snowmobile and secure with a
suitable stand.
3. Remove the lock nuts securing the wear bar to the
ski; then remove the wear bar.
INSTALLING
1. Install the wear bar into the ski making sure it is fully
seated using a rubber mallet.
2. Secure the wear bar with lock nuts. Tighten to 96 in.-
lb.
Drag Link (Bearcat/F-Series/
T-Series)
REMOVING
NOTE: On the F5 LXR to remove the drag link, it will
be necessary to remove the air silencer. Proceed to
Air Silencer (Liquid Cooled F-Series 2-Stroke) sub-
section in Section 3 and follow the REMOVING proce-
dure.
1. On the 1100 cc models, remove the hood and discon-
nect the oxygen temperature sensor; then remove the
exhaust springs securing the exhaust pipe to the man-
ifold, mounting tab, and resonator. Move and secure
the pipe out of the way.
NOTE: On the turbo model, loosen the intercooler
hose clamps at the intake pipe and the turbocharger;
then carefully work the intercooler upward until it
releases from the rubber grommets.
2. On the non-turbo 1100 cc models, remove the two
cap screws (A) securing the front end close-off cover
to the front end; then remove the cover and account
for the exhaust pipe mounting tab (B) from the right-
side cap screw.
Summary of Contents for Sno Pro 120
