2-91
2
IO050A
19. Place the impeller into position and secure with a cap
screw and washer. Be sure the rubber side of the
washer is lubricated with a light coat of grease and
directed toward the impeller. Apply blue Loctite
#243 to the threads of the cap screw and tighten to
108 in.-lb.
NOTE: For assembling purposes, lubricate the rub-
ber side of the washer before installing.
20. Apply High-Temp Sealant to the crankcase/water
pump cover seam (A); then install the dowel pins (C)
into the crankcase.
FC072C
NOTE: Do not allow sealant into the breather hole
(B) in the crankcase. If sealant gets into the hole,
carefully remove before proceeding.
21. Position the O-ring (lightly coated with oil) into the
water pump cover; then install the cover. Secure with
six screws; then using the pattern shown, tighten to
96 in.-lb.
FC134
0742-304
22. Noting the alignment dots, install the thermostat
housing with thermostat. Secure the housing with
cap screws and tighten to 96 in.-lb.
FC078A
FC073
23. With new gaskets, install the reed valve assemblies;
then secure the intake flanges to the crankcase.
Tighten in a crisscross pattern to 96 in.-lb.
CAUTION
When installing the ceramic/rubber seal into the impel-
ler, never touch the ceramic part of the seal. Make sure
components are clean and free of any dirt or contami-
nants.
CAUTION
If the rubber side of the washer is not positioned toward
the impeller, a coolant leak will result.
Summary of Contents for Sno Pro 120
