Arctic Cat HDX 500 2017 Page 134 Service Manual Download

Page: 134 / 190

133

Electrical System

The electrical connections should be checked periodi-

cally for proper function.

TESTING ELECTRICAL COMPONENTS

All electrical tests should be made using the CATT II or

the Fluke Model 77 Multimeter. The CATT II can return

data for certain components which are identified at the

beginning of their respective sub-section. If any other

type of meter is used, readings may vary due to internal

circuitry. When troubleshooting a specific component,

always verify first that the fuse(s) are good, that the

LED(s) are good, that the connections are clean and tight,

that the battery is fully charged, and that all appropriate

switches are activated.



NOTE: For absolute accuracy, all tests should be

made at room temperature of 68° F.



NOTE: Certain components and sensors can be

checked by using the EFI diagnostic system (see EFI

Diagnostic System in this section for more informa-

tion).

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Battery



NOTE: Preliminary checks may be performed on

this component using the diagnostic mode on the LCD

gauge (see EFI Diagnostic System in this section)

The battery is located under the seat on the driver’s side.

When installing the battery, always connect the positive

cable first; then connect the negative cable. When remov-

ing the battery, disconnect the negative cable first; then

disconnect the positive cable.

Ensure the positive battery cable is routed along the main

harness opposite side of the engine and secured using two

cable ties as shown. If it is ever required for these two

cable ties to be removed, replacement cable ties should

be installed in the same exact location.

HDX411A

After being in service, batteries require regular cleaning

and recharging in order to deliver peak performance and

maximum service life. The following procedures are rec-

ommended for cleaning and maintaining lead-acid batter-

ies. Always read and follow instructions provided with

battery chargers and battery products.



NOTE: Refer to all warnings and cautions provided

with the battery or battery maintainer/charger.

Loss of battery charge may be caused by ambient tem-

perature, ignition OFF current draw, corroded terminals,

self discharge, frequent start/stops, and short engine run

times. Frequent winch usage, snowplowing, extended

low RPM operation, short trips, and high amperage

accessory usage are also reasons for battery discharge.

Maintenance Charging



NOTE: Arctic Cat recommends the use of the

CTEK Multi US 800 or the CTEK Multi US 3300 for

battery maintenance charging. Maintenance charging

is required on all batteries not used for more than two

weeks or as required by battery drain.

1. When charging a battery in the vehicle, be sure the

ignition switch is in the OFF position.



NOTE: Be sure to maintain the fluid of the battery

at the UPPER LEVEL. Use only distilled water when

adding fluid to these batteries.

2. Clean the battery terminals with a solution of baking

soda and water.

3. Be sure the charger and battery are in a well-venti-

lated area and ensure the battery charger cables will

not contact any battery acid. Be sure the charger is

unplugged from the 110-volt electrical outlet.

4. Connect the red terminal lead from the charger to the

positive terminal of the battery; then connect the

black terminal lead of the charger to the negative ter-

minal of the battery.

5. Plug the battery charger into a 110-volt electrical

outlet.

Description

p/n

Fluke Model 77 Multimeter

0644-559

CATT II

0544-029

MaxiClips

0744-041

Test Plug/Code List

0486-219

Component data can be retrieved using the CATT II. Uti-
lize the Sensor Data screen.

Summary of Contents for HDX 500 2017































































































































































































Search results

Summary of Contents for HDX 500 2017

Reviews:

Related manuals for HDX 500 2017

Brands by name

Popular brands

Arctic Cat HDX 500 2017, Service Manual

Search results

Summary of Contents for HDX 500 2017

Reviews:

Related manuals for HDX 500 2017

Brands by name

Popular brands